SUBWOOFER POWER AMPLIFIER
KAC-8101D
INSTRUCTION MANUAL
© B64-3416-00/00 (MV)
Installation
Self-tapping screw
(ø4 × 16 mm)
Installation board, etc.
(thickness : 15 mm or more)
2CAUTION
• Do not install in the below locations;
(Unstable location, In a location that interferes with driving, In a location that gets wet, In a dusty location,
In a place that gets hot, In a place that gets direct sunlight, In a location that gets hit by hot air)
• Do not install the unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged.
• Install this unit in a location which allows heat to easily dissipate.
Once installed, do not place any object on top of the unit.
• The surface temperature of the amplifier will become hot during use. Install the amplifier in a place where
people, resins, and other substances that are sensitive to heat will not come into contact with it.
• When making a hole under a seat, inside the trunk, or somewhere else in the vehicle, check that there
is nothing hazardous on the opposite side such as a gasoline tank, brake pipe, or wiring harness, and be
careful not to cause scratches or other damage.
• Do not install near the dashboard, rear tray, or air bag safety parts.
• The installation to the vehicle should securely fasten the unit to a place in which it will not obstruct driving.
If the unit comes off due to a shock and hits a person or safety part, it may cause injury or an accident.
• After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal
lamps and windshield wipers operate normally.
English 3
Controls / Indicator
(W)
40
20
10
1
2
3
4
5
1 EXPANDER switch
5 INPUT SENSITIVITY control
When this switch is turned ON the dynamic
range is increased.
Set this control according to the pre-output level
of the center unit connected with this unit, or
to the maximum power output of the genuine-
accessory car stereo.
2 LPF (Low-Pass Filter) FREQUENCY control
This control adjusts the frequency band output
from this unit.
Use the diagram on the right as a guide.
NOTE
3 INFRASONIC switch
For the pre-output level or the maximum power
output, refer to the <Specifications> in the
instruction manual of the center unit.
Ultralow frequencies that cannot be reproduced
even by a subwoofer speaker do not become
sound but become unnecessary oscillations,
which affect the sound by causing distortion, etc.
Setting this switch to "15 Hz" or "25 Hz" cuts the
frequencies below the respective frequency.
This improves the reproduction performance
of the speakers by eliminating unnecessary
oscillations which will not become sound.
4 BASS BOOST switch
Sets the boost level for bass control.
• 12dB position:
BASS BOOST is +12 dB.
• OFF position:
BASS BOOST is OFF.
4 English
6
6 Power indicator
■ The protection function is activated in the
following situations:
When the power is turned on, the Power
indicator lights.
This unit is equipped with a protection function
for protecting this unit and your speakers from
various accidents or problems that can occur.
When the protection function is triggered, the Power
indicator goes off and the amplifier stops operating.
• When a speaker wire may be short-circuited.
• When a speaker output contacts ground.
• When the unit malfunctions and a DC signal is
sent to the speaker output.
If the Power indicator does not light when the
power is turned on, the protection function
may be activated. Check whether there is any
indication of trouble.
• When the internal temperature is high and unit
won’t operate.
• When a ground wire of the center unit
(cassette receiver, CD receiver, etc.) or this unit
is not connected to a metal part serving as
an electrical ground passing electricity to the
battery's negative - terminal.
English 5
Connection
■ Terminal names
7
8
9 0
!
@
# $
%
7 Fuse (40 A)
% Speaker level input terminals
NOTE
NOTE
If you can’t find the specified capacity fuse at your
store etc., consult your Kenwood dealer.
• The genuine-accessory car stereo shall have a
maximum power output of no more than 40 W.
• Do not connect the speaker output leads from
a power amplifier (Optional) to the speaker
level input terminals of this unit, for this may
cause malfunction or damage.
• Do not connect cables and leads to both RCA
cable input jacks and the speaker level input
terminals simultaneously, for this may cause
malfunction or damage.
• Connect the power control lead to a power
supply which can be turned ON/OFF by
the ignition key switch (ACC line). With this
connection, shock noise may be generated
when the power of the genuine-accessory car
stereo is switched ON/OFF.
8 Battery terminal
9 Ground terminal
0 Power control terminal
Controls the unit ON/OFF.
NOTE
Controls the unit power. Be sure to connect it
with all the systems.
! Speaker output terminals
As this unit accepts speakers with a minimum
impedance of 1 ohm, connect speakers with 1-
ohm or higher impedance to these terminals.
2CAUTION
The rated input of the speakers should be no
less than the maximum output of the amplifier.
Otherwise malfunction may result.
@ RCA cable ground lead terminal
When using an RCA cable with a ground lead
attached, connect the ground lead to this
terminal.
# LINE IN terminal
$ LINE OUT terminal
The signal that’s input from the line input
terminal is output.
6 English
■ Installation procedure
■ Wiring
Since there are large variety of settings and
connections possible according to applications, read
the instruction manual well to select the proper
setting and connection.
• Take the battery wire for this unit directly from the
battery. If it's connected to the vehicle’s wiring
harness, it can cause blown fuses etc.
• If a buzzing noise is heard from the speakers when
the engine is running, connect a line noise filter
(optional) to each of the battery wire.
• Do not allow the wire to directly contact the edge
of the iron plate by using Grommets.
• Connect the ground wire to a metal part of the car
chassis that acts as an electrical ground passing
electricity to the battery‘s negative - terminal.
Do not turn the power on if the ground wire is not
connected.
1. Remove the ignition key and disconnect the
negative - terminal of the battery to prevent
short circuits.
2. Set the unit according to the intended usage.
3. Connect the input and output wires of the units.
4. Connect the speaker wires.
5. Connect the power wire, power control wire and
grounding wire following this order.
6. Install the unit in the car.
7. Connect the negative - terminal of the battery.
• Be sure to install a protective fuse in the power
cord near the battery. The protective fuse should
be the same capacity as the unit’s fuse capacity or
somewhat larger.
• For the power cord and ground, use a vehicle
type (fireproof ) power wring cord with a current
capacity greater than the unit’s fuse capacity. (Use
a power wiring cord with a diameter of 5 mm2
(AWG 10) or greater.)
• When more than one power amplifier are going
to be used, use a power supply wiring wire
and protective fuse of greater current-handling
capacity than the total maximum current drawn by
each amplifier.
2WARNING
To prevent fire caused by a short in the wiring,
connect a fusible link or breaker nearby the battery’s
positive terminal.
2CAUTION
• If sound is not output normally, immediately turn
power off and check connections.
• Be sure to turn the power off before changing the
setting of any switch.
• If the fuse blows, check wires for shorts, then
replace the fuse with one of the same rating.
• Check that no unconnected wires or connectors
are touching the car body. Do not remove caps
from unconnected wires or connectors to prevent
short circuits.
• Connect the speaker wires to appropriate speaker
connectors separately. Sharing the negative wire
of the speaker or grounding speaker wires to the
metal body of the car can cause this unit to fail.
• After installation, check that the brake lamps,
winkers, and wipers work properly.
■ Speaker Selection
• The rated input power of the speakers that are
going to be connected should be greater than the
maximum output power (in Watts) of the amplifier.
Use of speakers having input power ratings that
are less than the output power of the amplifier will
cause smoke to be emitted as well as damage.
• Use speakers that have an impedance of 1Ω or
greater. When more than one set of speakers
are going to be used, calculate the combined
impedance of the speakers and then connect
suitable speakers to the amplifier.
4Ω
4Ω
4Ω
4Ω
2 Ω
8 Ω
Combined impedance
English 7
Connection
■ RCA cable or Speaker level input connection
(RCA cable Connections)
RCA cable ground terminal
#
RCA cable*
GND
#
$
CENTER UNIT
(CD receiver, etc.)
Right input
Left input
Power control wire
(Blue/ White)
(Speaker level input Connections)
Cable Color of the connector
Genuine-accessory car
stereo (No line output
center unit etc.)
White
Left
White/Black
Gray
Right
Car fuse box
Gray/Black
%
Battery
ACC
8 English
* Commercially available parts
■ Speaker wire connection
Lead terminal*
!
!
Subwoofer (L + R)
■ Power wire connection
8
9
0
Lead terminal*
Terminal cover
Extension wire*
Battery wire*
Ground wire*
Protective Fuse*
Battery
English 9
Troubleshooting Guide
What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.
Before calling service, first check the following table for possible problems.
PROBLEM
POSSIBLE CAUSE
SOLUTION
No sound.
(No sound from one side.)
(Blown fuse.)
• Input (or output) cables are
disconnected.
• Protection circuit may be activated. • Check connections by referring to
<Indicator>.
• Connect the input (or output)
cables.
• Volume is too high.
• Replace the fuse and use lower
volume.
• The speaker cord is shorted.
• After check the speaker cord
and fixing the cause of the short,
replace the fuse.
The output level is too small
(or too large).
The input sensitivity adjusting
control is not set to the correct
position.
Adjust the control correctly referring
to <Controls>.
The sound quality is bad.
(The sound is distorted.)
• The speakers wire are connected
with wrong + / -polarity.
• Connect them properly checking
the + / - of the terminals and
wires well.
• A speaker wire is pinched by a
screw in the car body.
• The switches may be set
improperly.
• Connect the speaker wire again so
that it is not pinched by anything.
• Set switches properly by referring
to <Controls>.
Specifications
Specifications subject to change without notice.
Audio Section
Max Power Output ................................................................................................................................................................................... 1000 W × 1
Rated Power Output
(4 Ω) (20 Hz – 200 Hz, 0.5 % THD)....................................................................................................................................................200 W × 1
(2 Ω) (100 Hz, 0.5 % THD)......................................................................................................................................................................400 W × 1
(1 Ω) (100 Hz, 1.0 % THD)......................................................................................................................................................................500 W × 1
Frequency Response (+0, –3 dB).................................................................................................................................................5 Hz – 200 Hz
Sensitivity (rated output) (MAX.) ..................................................................................................................................................................... 0.2 V
Sensitivity (rated output) (MIN.) ...................................................................................................................................................................... 5.0 V
Signal to Noise Ratio........................................................................................................................................................................................... 100 dB
Input Impedance.....................................................................................................................................................................................................10 kΩ
Low Pass Filter Frequency (18 dB/oct.) ..................................................................................................................50 – 200 Hz (variable)
Infrasonic Filter Frequency (18 dB/oct.)............................................................................................................................. OFF / 15 / 25 Hz
Bass Boost Circuit (90 Hz) .................................................................................................................................................................OFF / +12 dB
General
Operating Voltage.................................................................................................................................................. 14.4 V (11 – 16 V allowable)
Current Consumption (4 Ω, 10 % THD).........................................................................................................................................................31 A
Dimensions (W × H × D).....................................................................................................................................................285 × 57 × 268 mm
Weight.........................................................................................................................................................................................................................2.96 kg
10 English
|
JVC CRT Television AV 14FTT2 AV 21DTT2 AV 21LTT1 User Manual
JVC Digital Camera GR DVM1DU User Manual
JVC Flat Panel Television LT 47X899 User Manual
JVC MP3 Player XL PG7 User Manual
Kawasaki Drill 840517 User Manual
Kenmore Microwave Oven 72163102 User Manual
Kenwood Car Video System DDX5015BT User Manual
King Canada Drill KC 13C FC User Manual
KitchenAid Dishwasher KUDI01DL User Manual
KitchenAid Range KDRS407V User Manual