Carbon
Tower Heater
Instruction Booklet
KCF200
KCF200_IB_V4.indd
1
21/10/09 9:34 AM
Contents
Kambrook Recommends
Safety First
p4
Your Carbon Tower Heater
Quick Start Guide
p6
p7
Using Your Carbon Tower Heater
Care and Cleaning
p8
p11
p12
Warranty Details
KCF200_IB_V4.indd
3
21/10/09 9:34 AM
Kambrook Recommends Safety First
IMPORTANT: Please retain your
instruction book for future use.
At Kambrook, we believe that safe performance is the first priority in any
consumer product, so that you, our valued customer can confidently
use and trust our products. We ask that any electrical appliance that
you use be operated in a sensible fashion with due care and attention
placed on the following important operating instructions.
Important Safeguards For Your Kambrook
Carbon Tower Heater
• Avoid touching heater body while it is on,
some parts of the heater are hot.When
moving the unit switch off and hold the
heater by the handles where provided.
• Keep combustible materials such as
drapes and other furnishings at least 1.7
metres from the front, sides and rear of
the heater. Do not use heater to dry your
laundry.
at the power outlet then unplug heater
from the power outlet when not in use.
• Do not operate heater whilst asleep.
• Do not operate any heater with a
damaged cord or plug, or if heater
has been dropped or damaged in any
manner. Return heater to your nearest
service centre for examination, electrical
or mechanical adjustment or repair.
• Do not use outdoors.This heater is not
intended for commercial use, such as
construction sites.
• Do not locate the heater immediately
below a socket outlet when in use.
WARNING: In order to
avoid overheating do
not cover the heater.
• Do not use this heater with a
programmer, timer or any other
device that switches the heater on
automatically. Since a fire risk may exist
if the heater is covered or positioned
incorrectly.
• This heater is not intended for use in wet
or moist locations. Do not use this heater
in the immediate surroundings of a bath,
a shower or a swimming pool. Do not
immerse or allow liquids to be spilt on
heater.
• This heater has hot and arcing or
sparking parts inside. Do not use in areas
where petrol, paints, aerosols, or other
inflammable substances are used or
stored.
• Extreme caution and supervision is
necessary when this heater is used by or
near children, invalids or animals.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
• Important – this heater is intended for
floor use only.
• Do not operate the heater with the
power cord damaged, frayed or split,
wound around any part of the heater, or
in contact with heated surfaces of the
heater.
• Do not mount on ceiling or walls.
• Do not leave heater unattended.Always
switch off the heater at the controls and
4
KCF200_IB_V4.indd
4
21/10/09 9:34 AM
• Do not allow materials that have been
in contact with oil, petroleum based
products or drying fluids to come in
contact with the heater.
• Do not run the cord under carpeting
or cover the cord with rugs, runners or
the like.Arrange cord away from traffic
areas and where it will not be tripped
over.
• To disconnect heater turn the power to
OFF, then turn the control switch to off.
Turn off at the power outlet then remove
the plug from its outlet.
• Do not insert or allow foreign objects to
pass through the element guard, inlet
or outlet openings.This may cause an
electric shock, fire or damage the heater.
• To prevent a possible fire or heat
damage, allow ample space around the
heater (1.7m at front and 0.5m at the
rear, top and sides) and do not totally
or partially block the air inlet or outlets
in any manner. Check the openings
from time to time for accumulated
dust. Ensure long shag carpet does not
obstruct airflow under the unit.
heater to cool down before cleaning or
storing.
• The heater will not operate unless it is
placed on a flat, level surface as it is
fitted with a tilt switch.
• Always move the heater with the handle
provided.
• Use this heater only as described in this
instruction manual.Any other use not
recommended by the manufacturer
may cause fire electric shock or injury
and voids all warranties.
• Regularly inspect the supply cord, plug,
control settings, air inlets and outlets and
main housing for any damage. If found
damaged in any way, immediately
cease use of the heater and return
to Kambrook or an authorised service
agent for inspection or repair.
NOTE: This Kambrook Carbon
Tower Heater is electronically
controlled and will not operate
until the heater is plugged into
a 230V or 240V power point and
switched on.
• Do not touch hot metal surfaces.
• Switch off at the control switch and
power outlet, then unplug and allow
Important Safeguards For All Electrical
Appliances
• Fully unwind the power cord before use.
• Any maintenance other than cleaning
should be performed at an authorised
Kambrook Service Centre.
• Do not let the power cord hang over
the edge of a bench or table, touch hot
surfaces or become knotted.
• This appliance is for household use only.
Do not use this appliance for anything
other than its intended use. Do not use
in moving vehicles or boats. Do not use
outdoors. Misuse may cause injury.
• The installation of a residual current
device (safety switch) is recommended
to provide additional safety protection
when using electrical appliances. It
is advisable that a safety switch with
a rated residual operating current
not exceeding 30mA be installed in
the electrical circuit supplying the
appliance. See your electrician for
professional advice.
• The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
• It is recommended to regularly inspect
the appliance.To avoid a hazard do not
use the appliance if power cord, power
plug or appliance becomes damaged
in any way. Return the entire appliance
to the nearest authorised Kambrook
Service Centre for examination and/or
repair, or contact Customer Service on
1300 139 798
5
KCF200_IB_V4.indd
5
21/10/09 9:34 AM
Your Kambrook Carbon Tower Heater
1. 1000 watt heating elements for
Control Panel
6. Convenient 3hr auto-off timer
7. 2 heat setting modes
efficient heating
2. ThermoGuard protection for
peace of mind
8. 60° degree oscillation for warmth
3. Carbon heating elements for
gentle heating and minimal
moisture loss
throughout the room
9. Power-on indicator light
4. Convenient carry handle
5. Safety tip-over cut-out switch
6
KCF200_IB_V4.indd
6
21/10/09 9:34 AM
Quick Start Guide
Turning the
heater on after
assembly of
heater
Setting the
heating
mode
ON
CAUTION: DO NOT COVER
MODE OFF
LOW
TIMER 180
150
0 MINS
30
ON
MODE OFF
LOW
HIGH
TIMER 180
150
0
MINS
30
HIGH
SWING
60
120
90
60
120
90
Set the MODE
dial to the OFF
position and
TIMER dial to 0
MINS.
Plug the cord
into a 230V or
240V power
point and
Turn the MODE
dial to the high
or low setting.
Turn the TIMER
dial to the ON
position.
switch on.
Setting the
oscillation
Turning the
heater off
MODE OFF
LOW
SWING
HIGH
Turn the heater
off by turning
the MODE dial
to the OFF
Press the SWING
button to
activate. Press
again to stop
the oscillation.
position.
• Fit window coverings like curtains to
Hints/Tips to Retain Heat in
Your Home
limit winter heat loss
• Put draft stoppers, such as a rolled
up towel, at the bottom of outside
doorways to keep out cold air
• Keep the heat in and the cold out by
installing wall and ceiling insulation.
• Avoid placing items too close to the
heater (both at the front and back)
for optimal air flow
• Don’t overheat your home.The
temperature of a heated room in
winter should be 18-21°C
• Your heater will work more
efficiently if you stick to Kambrook’s
recommended clearance spaces
• Choose the right size heater for the
room type you want to heat
• Zone off unoccupied rooms by closing
doors and only heat the main living
areas
7
KCF200_IB_V4.indd
7
21/10/09 9:34 AM
Using Your Carbon Tower Heater
Remove any promotional material or
packaging from the heater.
Unwind the cord to its full length
and place the heater on a firm, level
surface in a stable upright position.
Visually inspect the air inlet and outlets
to ensure there are no blockages.
Assembling Your Heater
Remove all items from the packaging
- the carbon tower body, front and
rear bases. Unscrew the two screws
Use the screws provided to secure the
from the base of the tower body.
tower body to the base.
To join the front and rear bases
together, initially feed the cord
between the two parts of the base.
Position the front base over the
corresponding posts of the rear
base, and press down to fit the bases
together. Ensure the cord remains
within the channel formed when the
two halves come together.
Clip the cord into the straight slot,
running from the centre to the edge
of the base. Ensure the cord is tidily
fitted into the channel, and flush with
the base.
Turn the Carbon Tower Heater back
to an upright position. It is now ready
to use.
Turning Your Heater On
Always place the heater on a firm,
level surface in a stable upright
position.
Ensure the MODE dial is turned to the
OFF position, and the TIMER dial is
turned to the 0 MINS position.
Plug the cord into a 230V or 240V
power point and switch on.
NOTE: To avoid an electrical
circuit overload, it is
recommended that no other
appliances are plugged into
the same circuit as your heater,
when it is in use.
Turn the carbon tower body upside
down.Align and position the base
over the corresponding posts on the
rear of the tower body. Push down the
base onto the tower body until it is
firmly held into position.
The Power-On Indicator, on the front
of the heater, will illuminate when the
heater is turned on.
8
KCF200_IB_V4.indd
8
21/10/09 9:34 AM
Setting the Auto-Off Timer
The TIMER function works in all
Setting the Heating Mode
operating modes, and switches the
unit off after a preset number of hours.
CAUTION: DO NOT COVER
Turn the TIMER dial to activate the
timer settings.The timer can be set for
up to 3 hours.
ON
MODE OFF
LOW
TIMER 180
150
0
MINS
30
HIGH
SWING
For setting times less than 1 hour, turn
the timer dial past the 2 hours mark,
then turn back to the desired time.
60
120
90
The unit will then switch itself off after
the selected time has passed.
By turning the TIMER dial to ON, this will
ensure the heater runs continuously,
and will not turn itself off.
To control the heater, turn the MODE
dial as follows.
The Heat Setting dial has 3 modes:
OFF - Shuts off the heater
Setting the Oscillation
The oscillation function works in all
operating modes.
1
2
-
-
Low heat setting (500W)
High heat setting (1000W)
Press the SWING button once to
activate.The heater will begin to
oscillate from side to side.
Press the SWING button again to stop
the heater from oscillating.
Once the heat setting has been
selected, turn the TIMER dial to the ON
position.This will activate the heater.
NOTE: The Carbon Tower Heater
will not activate while the Timer
dial is set at 0 MINS.
To switch the heater off, turn the
MODE dial to the OFF position.
NOTE: This heater features a tip-
over switch. If the heater tips
over, it will automatically switch
off. Once placed back into the
upright position, the heater will
activate again.
9
KCF200_IB_V4.indd
9
21/10/09 9:34 AM
Using Your Carbon Tower Heater
continued
ThermoGuard Overheating
Safety Device
Your heater is fitted with a safety
device that switches off the heater
in the event of overheating. Should
this heater stop working, turn off the
heater and inspect the air inlet and
outlet for blockages.Wait at least five
minutes for the protection system to
reset before attempting to restart the
heater.
If the heater fails to operate or the
safety device switches off again,
return the heater to your nearest
Kambrook service centre for
examination or repair.
10
KCF200_IB_V4.indd 10
21/10/09 9:34 AM
Care and Cleaning
Ensure that the heater is switched off
and disconnected from the power
point before cleaning.
Use a clean, dry cloth to clean the
external surfaces of the heater. If
the heater has collected dust or dirt
inside the unit or around the elements,
have the unit cleaned by a qualified
service agent. Do not operate the
heater in this condition.
Do not attempt to open the element
guard or the case of the heater at
any time as there are no customer
serviceable parts inside.
When not in use, store the heater
(preferably in its original box) in a cool,
clean and dry location.
11
KCF200_IB_V4.indd 11
21/10/09 9:34 AM
Kambrook 12 Month Replacement Warranty
In Australia, this Kambrook Replacement Warranty
The Kambrook Replacement Warranty does not
apply to any defect, deterioration, loss, injury or
damage occasioned by, or as a result of, misuse
or abuse, negligent handling or if the product has
been used other than in accordance with the
instructions.The Kambrook Replacement Warranty
excludes breakables such as glass and ceramic
items, consumable items and normal wear and
tear.
does not affect the mandatory statutory rights
implied under the Trade Practices Act 1974
and other similar State and Territory legislation
relating to the appliance. It applies in addition
to the conditions and warranties implied by that
legislation.
In New Zealand, this Kambrook Replacement
Warranty does not affect your mandatory statutory
rights implied under the Consumer Guarantees
Act 1993 in relation to the appliance. It applies in
This Kambrook Replacement Warranty is void if
there is evidence of the product being tampered
addition to the conditions and guarantees implied with by unauthorised persons.
by that legislation.
If the product includes one or a number of
This Kambrook Replacement Warranty is valid only accessories only the defective accessory or
in the country of purchase, but other statutory
warranties may still apply.
product will be replaced. Subject to your statutory
rights, in the event of Kambrook choosing
to replace the appliance, the Kambrook
Replacement Warranty will expire at the original
date, i.e. 12 months from the original date of
purchase.
This Warranty card and the purchase receipt for this
product are to be retained as proof of purchase
and must be presented if making a claim under
the Kambrook Replacement Warranty. Please note
that under any applicable statutory warranty you
In the event that you need some assistance
are not required to produce these documents, but with your Kambrook appliance, please contact
may be required to provide a proof of purchase.
our Customer Service Department on 1300 139
798 (Australia) or 09 271 3980 (New Zealand).
Alternatively, visit us on the website at
www.kambrook.com.au
Kambrook warrants the purchaser against defects
in workmanship and material for a period of 12
months domestic use from the date of purchase
(or 3 months commercial use).
Kambrook 12 Month Replacement Warranty
Your Purchase Record (Please Complete)
Attach a copy of the purchase receipt
here.
Date Of Purchase ________________________________
Model Number ___________________________________
Serial Number ____________________________________
Purchased From __________________________________
(Please don’t return purchase record
until you are making a claim)
Kambrook - New Zealand
Private Bag 94411
Botany, Manukau
Auckland 2141
New Zealand
Customer Service Line/Spare Parts
0800 273 845 or 09 271 3980
Kambrook - Australia
Building 2, Port Air Industrial Estate
1A Hale Street
Botany NSW 2019
Australia
Customer Service Line 1300 139 798
Customer Service Fax 1800 621 337
Customer Service Fax 0800 288 513
Due to continual improvement in design or otherwise, the product you
purchase may differ slightly from the illustration in this book. Issue 1/10
KCF200_IB_V4.indd
1
21/10/09 9:33 AM
|