Jasco Universal Remote RM24948 User Manual

RM24948  
Universal Remote  
Instruction Manual  
 
Button Functions  
Code Entry using the Code List  
Red Indicator  
Lights when any  
button is pressed.  
1. Press and hold the SETUP button until  
the red indicator stays on, then release  
the SETUP button.  
POWER Turns  
product On or Off.  
SETUP Used to setup  
the remote, and for  
code search function.  
2. Press and release the desired device  
button (TV, VCR, etc.). The red indicator  
blinks, then stays lit.  
TV, CBL/AUX, VCR/DVD  
Selects product to be  
operated.  
3. Enter the 4 digit code for  
your brand of TV, VCR,  
etc., from the Library Code  
Table by using the Rewind,  
Play, and Fast Forward  
buttons.  
CHANNEL Up/Down  
Changes the channels.  
Also controls DVD SKIP  
functions.  
MUTE Turns off the  
TV sound, while the  
picture remains.  
Use the REW button to enter the first digit.  
Use the Play button to enter second digit.  
Use the FF button to enter the third digit.  
VOLUME UP/DOWN  
Changes the volume  
level of the product,  
normally the TV.  
RECORD, PLAY, STOP,  
REW, FF, PAUSE VCR/DVD  
control buttons operate  
your VCR or DVD even  
when the remote is set to  
operate the TV.  
For Example: To enter code 013, don’t press REW,  
press Play once, and FF three times. The red LED  
blinks off with each keypress.  
4. Press the Stop button to save the code.  
Note: The REC button must be pressed TWICE to  
record from your VCR. For some brands of VCRs, you  
might need to press the REC button once, then press it  
again for three seconds.  
Note: for a valid code, the red LED turns off. For an  
invalid code, the red LED blinks rapidly for three  
seconds before going off.  
5. With your device on, press POWER. If the  
device turns off, no further programming is  
required. Note: If some buttons do not operate  
your equipment, try one of the other codes for  
your brand.  
4
5
 
Setting up using Code Search  
UsingYour Remote  
If you cannot find a 4 digit code in the Code Table  
that operates your TV, try searching for the code as  
follows:  
Code Retrieval  
Code Retrieval lets you identify the four digit library  
code stored under your device button. For example,  
if you want to find out what four digit code is stored  
under your TV device button, follow the six steps  
below:  
1. Manually turn on the device (TV, VCR, etc.) to  
be controlled.  
2. Press and hold the SETUP button until  
the red indicator stays on, then release  
the SETUP button.  
1. Press and hold the SETUP button until  
the red indicator stays on, then release  
the SETUP button.  
3. Press and quickly release the desired  
device button (TV, VCR, etc.). The red  
indicator blinks off once.  
2. Press and release the desired device  
button (TV, VCR, etc.). The red  
indicator blinks, then stays lit.  
4. Press the POWER button  
repeatedly (up to 300 times) until  
the device to be controlled turns off.  
The red indicator blinks off with each  
button press.  
3. Press and release the SETUP button.  
The red indicator blinks once and  
remains lit.  
4. To find the first digit for the code stored  
under the device button pressed in step  
2, press REW and count the number of  
blinks.  
5. Press and release STOP to install the  
code.  
5. To find the second digit, press Play  
and count the number of blinks.  
Write your codes down here for easy reference  
later.  
6. To find the third digit, press FF and  
count the number of blinks.  
Device  
Device stored Code  
TV  
TV  
CBL/AUX  
VCR/DVD  
6
7
 
UsingYour Remote, cont.  
UsingYour Remote, cont.  
Controlling Devices with Separate Power  
On and Off Buttons  
Setting ALL Volume/Mute Control to any  
one Mode  
Some GE, RCA and ProScan models require you to  
press the device button for more than one second  
to turn the device on and the POWER button to turn  
the device off.  
This routine can set all Modes to “punch-through” to  
any one chosen Mode for Volume/Mute button  
control without the needing to change to that Mode.  
1. Press and hold SETUP until the red  
indicator turns on, then release SETUP.  
Controlling Combo Devices  
Some Combo devices (e.g. TV/VCR, TV/DVD,  
DVD/VCR, etc.) will require you to set up two  
different Mode buttons to control both parts of the  
Combo device. For example, if you have a TV/DVD  
Combo, you might need to set up one code under  
the TV button to control the TV part AND a  
separate code (under any other Mode button) to  
control the DVD part.  
2. Press and hold MUTE until the red  
indicator blinks off, then release MUTE.  
3. Press and release the desired Mode  
button (TV, VCR) for Volume/Mute control,  
the red indicator blinks then stays on.  
4. Press and release MUTE and the red  
indicator turns off. The red indicator will  
blink rapidly for three seconds if the Mode  
you have selected has no Volume/Mute  
control.  
VCR/DVD Punch-Through  
This remote allows the 6 VCR transport buttons  
(i.e. PLAY, PAUSE, STOP, FF, REWIND, and REC)  
to Punch-Through control from any Mode  
programmed with TV, SAT or Cable codes to the  
last VCR, or DVD programmed Mode you used.  
This feature will not operate if the programmed TV,  
SAT or Cable code has its own VCR transport  
button control e.g. a TV Combo, SAT/PVR, etc.  
All other Modes will now punch-through to your  
chosen Mode for Volume/Mute control.  
Returning Volume/Mute Control to Initial  
Default Settings  
This routine returns Volume/Mute control to its  
default (factory) settings i.e. all device Modes  
use their own Volume/Mute control if present or  
else they will punch-through control to the TV  
Mode device.  
Volume/Mute Control and Punch-Through  
This remote lets you select which device Mode  
controls your Volume/Mute buttons. The remote is  
initially set for all device Modes to use their own  
Volume/Mute control if present. If the programmed  
code has no Volume/Mute operation of its own then  
those buttons will punch-through control to the TV  
Mode device without needing to change to TV  
Mode.  
1. Press and hold SETUP until the red  
indicator turns on, then release SETUP.  
2. Press and hold MUTE until the red  
indicator blinks off, then release MUTE.  
3. Press and release MUTE and the red  
indicator turns off. Volume/Mute control  
is returned to its default (factory)  
Any Mode chosen for Volume/Mute control  
MUST have its own Volume/Mute function or  
the Volume/Mute buttons will do nothing.  
settings.  
8
9
 
Troubleshooting  
90 Day Limited Warranty  
Remote does not operate your product.  
Jasco Products Company warrants this product to  
be free from manufacturing defects for a period of  
ninety days from the original date of consumer  
purchase. This warranty is limited to the repair or  
replacement of this product only and does not  
extend to consequential or incidental damage to  
other products that may be used with this unit. This  
warranty is in lieu of all other warranties express or  
implied. Some states do not allow limitations on  
how long an implied warranty lasts or permit the  
exclusion or limitation of incidental or consequential  
damages, so the above limitations may not apply to  
you. This warranty gives you specific rights, and  
you may also have other rights which vary from  
state to state. If unit should prove defective within  
the warranty period, return prepaid with dated proof  
of purchase to:  
Press the device button of the product you want  
to control.  
Program the remote with a new code.  
Install new batteries. (You might have to  
reprogram your remote after installing new  
batteries.)  
Remote may not be compatible with your  
product.  
Remote does not operate some features of  
your product.  
Sometimes a particular code might operate  
some features but not all. Try programing  
remote with a new code.  
Remote may not be able to operate all features  
of your product or button names might be  
different than your product.  
Jasco Products Company  
311 N.W. 122nd  
Oklahoma City, OK 73114  
Red Indicator blinks after you program a  
product code.  
Remote did not accept the code.  
Try to program the code again or try a different  
code.  
Lost Your Codes?  
Enclosed with this remote is a sticker on which you  
should write the codes for each device you  
programmed. Apply the sticker to the back of the  
remote or somewhere convenient for future  
reference.  
Also on the sticker is our website address which,  
should you lose your codes or programming  
instructions, you can find available on our website:  
10  
11  
 
RM24948  
Universal Remote  
Instruction Manual  
Jasco Products Company  
311 N.W. 122nd  
Oklahoma City, OK 73114  
Made in China  
RM24948-03/05  
 

IOGear Network Router GHPB01 User Manual
JL Audio Stereo Amplifier G1700 User Manual
John Deere Compact Loader 410B User Manual
Karcher Vacuum Cleaner K 291 MD User Manual
Kathrein Stereo Receiver MVG 10 User Manual
Kenwood Car Stereo System KDC 132 User Manual
Keys Fitness Treadmill EC3500HRC User Manual
Kidde Carbon Monoxide Alarm KN COPD 3 UK User Manual
KitchenAid Blender 4KFP750BU0 User Manual
Konica Minolta Printer 1250E User Manual