JVC TV Cables DT V1700CG User Manual

MULTI-FORMAT MONITOR  
INSTRUCTIONS  
DT-V1700CG  
For Customer Use:  
Enter below the Serial No. which is located on the rear of  
the cabinet. Retain this information for future reference.  
UNDER  
SCAN  
PULSE  
CROSS  
COLOR  
OFF  
DEGAUSS  
MENU  
POWER  
SLOT 1  
SLOT 2  
SLOT 3  
A
B
C
D
E
F
BLUE  
ASPECT  
AREA  
INPUT SELECT  
VOLUME  
CHECK  
MARKER  
Model No.  
Serial No.  
:
:
DT-V1700CG  
The illustration above shows the DT-V1700CG with provided  
wide mask attached.  
Untitled-1  
1
01.3.27, 9:58  
 
CONTENTS  
SAFETY PRECAUTIONS........................................................................2  
CONTROLS AND FEATURES ................................................................4  
CONTROLS AND FEATURES  
(INPUT CARD: OPTIONAL)....................................................................6  
PREPARATION .......................................................................................8  
BASIC MENU OPERATIONS  
(MAIN MENU, SETUP MENU) ................................................................9  
HOW TO USE “MAIN MENU...............................................................10  
HOW TO USE “SETUP MENU............................................................13  
HOW TO USE EXTERNAL CONTROL .................................................17  
TROUBLESHOOTING...........................................................................19  
SPECIFICATIONS .................................................................................21  
3
Untitled-1  
3
01.3.27, 9:58  
 
CONTROLS AND FEATURES  
FRONT VIEW  
<Front Panel>  
1
U
N
D
E
R
P
U
L
S
E
C
O
L
O
R
D
E
G
A
U
S
S
S
C
A
N
C
R
O
S
S
O
F
F
POWER  
SLOT 1  
SLOT 2  
SLOT 3  
A
B
C
D
E
F
M
E
N
U
B
L
U
E
A
S
P
E
C
T
A
R
E
A
INPUT SELECT  
V
O
L
U
M
E
C
H
E
C
K
M
A
R
K
E
R
2 3 4 5  
6 7  
9
10 11 12 16 17 18 19 20 21 22 23  
UNDER  
SCAN  
PULSE  
CROSS  
COLOR  
OFF  
DEGAUSS  
POWER  
SLOT 1  
SLOT 2  
SLOT 3  
A
B
C
D
E
F
MENU  
SCREENS  
CHECK  
ASPECT  
AREA  
INPUT SELECT  
VOLUME  
MARKER  
13 14 15  
8
8
9
1 Tally lamp  
MENU button  
Lights when the tally control signal is ON. The tally control  
signal is input through the MAKE remote terminal. For  
details, refer to Page 17.  
Displays, adjusts or closes a menu screen.  
DEGAUSS button/lamp  
Press the DEGAUSS button. The button lights and  
degaussing is performed automatically. When the  
degaussing is completed, the light goes off.  
PHASE adjustment knob  
Adjusts picture hue. Turn the knob to the left to make the  
picture redder, and turn it to the right to make the picture  
greener.  
2
3
4
5
10 UNDER SCAN button/lamp  
Press the UNDER SCAN button. The button lights and  
the screen is reduced (under-scan) and the whole screen  
is displayed. When the UNDER SCAN button is pressed  
while lit, the light goes off and the screen returns to  
normal size (over-scan). Use this function to check the  
whole screen.  
CHROMA adjustment knob  
Adjusts picture color density. Turn the knob to the left to  
make the picture color lighter, and turn it to the right to  
make the picture color deeper.  
BRIGHT adjustment knob  
Adjusts picture brightness. Turn the knob to the left to  
make the picture darker, and turn it to the right to make  
the picture brighter.  
NOTE: This function is invalid with the RGB-input screen.  
PULSE CROSS button/lamp  
11  
Press the PULSE CROSS button. The picture is  
separated into 4 parts. The synchronized signal displayed  
in the shape of a cross separating the parts. The screen  
automatically brightens to make it easier to confirm  
synchronized sections easy. When the PULSE CROSS  
button is pressed while lit, the light goes off and the  
normal screen is restored.  
CONTRAST adjustment knob  
Adjusts picture contrast. Turn the knob to the left to make  
the picture contrast lower, and turn it to the right to make  
the picture contrast higher.  
6 VOLUME buttons  
NOTE: This function is invalid with the RGB-input screen.  
Adjusts the speaker volume. Also used to set or adjust  
menu screen items.  
Menu select buttons  
Selects menu screen items or set-up menu screen.  
7
4
Untitled-1  
4
01.3.27, 9:58  
 
REAR/SIDE VIEW  
<Rear Panel>  
<Side Panel>  
REMOTE  
MAKE  
RS-232C  
24  
25  
28  
26  
MAIN POWER  
27  
Refer to pages 8 and 9 for correspondence between the  
input terminals and the INPUT SELECT buttons.  
12 COLOR OFF button/lamp  
Press the COLOR OFF button. The button lights and the  
screen becomes monochrome. When the COLOR OFF  
button is pressed while lit, the light goes off and the  
normal screen is restored.  
Power lamp  
22  
Unlit  
: The main power is OFF.  
Orange : The main power is ON, but the monitors power  
is OFF (in stand-by mode).  
Green : The main power is ON, and the monitors power  
is ON (in normal operation mode).  
Use this function to confirm the noise in the brightness  
signal or to confirm the white balance.  
NOTE: This function is invalid with the RGB-input screen.  
SCREENS CHECK button/lamp  
Press the SCREENS CHECK button. The button lights  
and the screen changes in the following order:  
13  
23 POWER switch  
Press the power switch to turn the monitors power ON or  
OFF when the main power is ON.  
Normal screen[Red screen[Green screen  
NOTE: When RUSH DELAY TIME is set to MODE 2 in  
the set-up menu, it takes approx. 3.2 seconds for  
the power to actually turn ON after the power  
switch is pressed.  
Blue screenp  
Press the SCREENS CHECK button when the blue  
screen is displayed. The light goes off and the normal  
screen is restored.  
REMOTE (external control) terminals  
Terminals for controlling the monitor from an external unit.  
RS-232C terminal (Upper):  
24  
Use this function to confirm or adjust CHROMA or  
PHASE.  
NOTE: This function is invalid with the RGB-input screen.  
Enables the monitor to be controlled from a personal  
computer via serial communication.  
MAKE terminal (Lower):  
Enables the monitor to be controlled by closing the circuit  
(point of contact) connected to the terminal.  
14 ASPECT button/lamp  
When the ASPECT button is pressed while the screen  
ratio is 4:3, the button lights and the screen ratio changes  
to 16:9. When the ASPECT button is pressed while lit, the  
light goes off and the normal screen is restored.  
NOTE: This function is invalid with the RGB-input screen.  
25 Input card slots (SLOT 1 SLOT 3)  
Optional input cards can be installed in these slots. Input  
cards are not provided when you purchase the monitor.  
NOTE: It is not possible to input video or audio signals to  
the monitor when no input cards are installed.  
15 AREA MARKER button/lamp  
When the AREA MARKER button is pressed while the  
screen ratio is 16:9, the button lights and the white  
marker is displayed. This shows the screen size (area)  
set on the menu. When the AREA MARKER button is  
pressed while lit, the light goes off and the normal screen  
is restored.  
Main power switch  
26  
Press the switch to turn the main power ON or OFF.  
When the main power is ON, the power lamp on the front  
panel lights in yellow and the monitor enters the stand-by  
mode.  
NOTE: This function is invalid with the RGB-input screen.  
INPUT SELECT buttons/lamps  
21  
16  
I : ON : OFF  
Press the unlit button. The button lights and the input  
signal is changed. (any other lit button goes off.)  
When the lit button is pressed, the status of the current  
input signal is displayed (for approx. 3 seconds). Buttons  
A through F correspond to the signals input via the input  
cards installed in SLOT 1 through SLOT 3.  
27  
28  
AC inlet  
Power input connector. Connect the provided AC power  
cord to an AC outlet (120 V AC, 50 Hz/60 Hz).  
Built-in speaker (monaural)  
Outputs the input audio.  
A, B : select the picture from the SLOT 1 input card.  
C, D : select the picture from the SLOT 2 input card.  
E, F : select the picture from the SLOT 3 input card.  
5
Untitled-1  
5
01.3.27, 9:58  
 
CONTROLS AND FEATURES  
(INPUT CARD: OPTIONAL)  
COMPONENT/RGB INPUT CARD (OPTIONAL:  
IF-C01COMG)  
Video input/output terminals  
Input (IN) and output (OUT) terminals for component  
(color deference) or RGB signals.  
1
G/Y  
The IN and OUT terminals are bridge-connected.  
(When no cable is connected to the OUT terminal, the  
input signal is automatically terminated.)  
Select component signal : press INPUT SELECT A/C/E  
button  
IN  
B/P  
OUT  
/B-Y  
B
R
1
IN  
R/P  
OUT  
/B-Y  
Select RGB signal  
: press INPUT SELECT B/D/F  
button  
IN  
IN  
IN  
OUT  
OUT  
OUT  
2
Synchronized signal input/output terminals  
Input (IN) and output (OUT) terminals for the vertical,  
horizontal or complex synchronized signals.  
The synchronized signals from these terminals have  
priority over other terminals. When no synchronized signal  
is input to these terminals, the synchronized signal from  
the video input/output terminals (G/Y terminals) is valid.  
The IN and OUT terminals are bridge-connected.  
(When no cable is connected to the OUT terminal, the  
input signal is automatically terminated.)  
HD/C  
VD  
S
4
2
3
AUDIO  
IN  
OUT  
Audio input/output terminals  
3
Compatible signal formats:  
480/60i, 576/50i, 480/50p, 480/60p, 720/60p, 1035/60i,  
1080/50i, 1080/60i  
Input (IN) and output (OUT) terminals for audio signals.  
The IN and OUT terminals are bridge-connected.  
4 Connection terminal (to a Multi-Format Monitor)  
Attach to the connection terminal of your multi-format  
monitor.  
VIDEO INPUT CARD (OPTIONAL: IF-C01PNG)  
1 Video input/output terminals  
Input (IN) and output (OUT) terminals for video signals.  
The IN and OUT terminals are bridge-connected.  
(When no cable is connected to the OUT terminal, the  
input signal is automatically terminated.)  
Select VIDEO 1 : press INPUT SELECT A/C/E button  
Select VIDEO 2 : press INPUT SELECT B/D/F button  
VIDEO1  
IN  
IN  
OUT  
VIDEO2  
1
OUT  
2 S-video input terminal  
Input terminal for the S-video signal.  
Y/C IN  
2
3
When an S-video signal is input to this terminal and a  
video signal is input to VIDEO 2, the S-video signal has  
priority over the video signal.  
When choosing the S-video input, press INPUT SELECT  
B/D/F button.  
5
EXT.SYNC  
IN  
AUDIO1  
OUT  
3 Synchronized signal input/output terminals  
Input (IN) and output (OUT) terminals for the complex  
synchronized signals.  
IN  
OUT  
4
AUDIO2  
The synchronized signals from these terminals have priority  
over signals from other terminals. When no synchronized  
signal is input to these terminals, the synchronized signal  
from the video input/output terminals is valid.  
The IN and OUT terminals are bridge-connected.  
(When no cable is connected to the OUT terminal, the  
input signal is automatically terminated.)  
Compatible signal formats:  
NTSC, PAL, black-and-white (50 Hz/60 Hz)  
* You can select AUTO(automatic selection), NTSCor  
PALin SETUP MENU when switching NTSC or PAL.  
Normally select AUTO. However, if the input signal is  
unstable, select NTSC or PAL.  
4
Audio input/output terminals  
Input (IN) and output (OUT) terminals for audio signals  
corresponding to VIDEO 1 and VIDEO 2. The IN and  
OUT terminals are bridge-connected.  
5 Connection terminal (to a Multi-Format Monitor)  
Attach to the connection terminal of your multi-format  
monitor.  
6
Untitled-1  
6
01.3.27, 9:58  
 
SDI INPUT CARD (OPTIONAL: IF-C01SDG)  
Output terminal for a selected component  
1
serial digital signal  
Output terminal for s selected digital signal (the input  
displayed on the screen). The output signal is cable-  
compensated.  
NOTE: When the monitors power is OFF, no digital  
signal is output.  
SWITCHED  
OUT  
1
2
IN  
IN  
SDI 1  
SDI 2  
Input terminals for component serial digital  
2
signals  
4
Input terminals for the digital signal.  
Select SDI 1 : press INPUT SELECT A/C/E button  
Select SDI 2 : press INPUT SELECT B/D/F button  
AUDIO1  
3 Audio input/output terminals  
IN  
OUT  
3
Input (IN) and output (OUT) terminals for the analog  
signals corresponding to SDI 1 and SDI 2.  
NOTE: This input card cannot decode audio data even if  
contained in the input digital signal.  
AUDIO2  
Connection terminal (to a Multi-Format  
4
Monitor)  
Compatible signal formats: 480/60i, 480/50i  
Attach to the connection terminal of your multi-format  
monitor.  
7
Untitled-1  
7
01.3.27, 9:58  
 
PREPARATION  
INSTALLING THE INPUT  
ATTACHING THE WIDE  
CARD  
MASK  
Optional input cards are necessary to use the functions of this  
monitor. Before mounting the monitor or connecting other  
equipment to the monitor, be sure to install the input cards.  
A wide mask is provided with the monitor. This changes the  
viewable screen area to the 16:9 aspect ratio.  
The wide mask cannot be attached to the monitor after the  
monitor is mounted in a rack. Mount the wide mask before  
installing the monitor in a rack.  
1. Turn off the Multi-Format Monitors main  
power and unplug the power cable from  
the AC outlet.  
2. Unscrew the screws and remove the slot  
cover from the slot (on the rear side of the  
monitor) in which you are going to install  
the card.  
1. Prepare the provided wide mask and 4  
screws (for attaching).  
2. Attach the wide mask to the monitor.  
Slot cover  
Rear side of the DV-1700CG  
multi-format monitor  
3. Insert the Input Cards board (green-  
colored) into the slot, fitting the board into  
the guide rails on the top and bottom of  
the slot.  
3. Secure the wide mask with the screws (fix  
2 screws each to both right and left side).  
Fit the board to  
the guide rails.  
Knob  
Guide rails  
Input card (the illustration shown  
is of the IF-C01PNG)  
Knob  
When detaching the wide mask, follow this procedure in  
reverse.  
4. Push the Input Card in so that its front  
panel touches the monitors rear panel.  
5. Secure the Input Card by replacing the  
screws removed in Procedure 2.  
NOTE :Do not touch the terminal connected to the monitor or  
board pattern.  
Do not remove slot covers from the monitors slots if  
they are not in use.  
8
Untitled-1  
8
01.3.27, 9:58  
 
BASIC MENU OPERATIONS  
(MAIN MENU, SETUP MENU)  
ABOUT MENU SCREENS  
BASIC MENU OPERATION  
This monitor features a MAIN MENU (main menu screen) and  
a SETUP MENU (setup menu screen).  
To select an item,  
Press the or  
buttons to move the cursor (4) on the  
The MAIN MENU contains the functions normally used, and  
the SETUP MENU contains the settings required for initial  
setup.  
Menu Screens and select the desired item.  
To set (select) or adjust an item,  
Press the  
item.  
or  
buttons to select or adjust the desired  
<MAIN MENU>  
<SETUP MENU>  
When the desired item has other menus (hierarchical  
menus),  
APERTURE CONTROL  
FUNCTION SETTING  
SLOT CONDITION  
sub menu POSITION :LOWER  
AREA MAKER  
AREA MAKER-R  
CENTER MAKER  
COLOR MATRIX  
PICTURE SUB ADJ.  
COLOR TEMP/BAL.  
Press the  
To return to the former Menu Screen,  
Press the button.  
button to display the lower hierarchical menu.  
:OFF  
:OFF  
:OFF  
SIZE/POSI.ADJ.  
DISTORTION ADJ.  
STATUS DISPLAY  
CONTROL LOCK  
all reset  
:ON  
MENU  
EXIT:MENU ENTER:+ SELECT:  
EXIT:MENU ENTER:+ SELECT:  
<MAIN MENU>  
<APERTURE CONTROL>  
MAIN MENU (main menu screen)  
SETUP MENU  
(setup menu screen)  
APERTURE CONTROL  
SLOT CONDITION  
sub menu POSITION :LOWER  
LEVEL  
:00  
:HIGH  
CONTROL FREQ.  
sub menu  
reset  
AREA MAKER  
:OFF  
:OFF  
:OFF  
NOTE :The contents of menus vary depending on the input  
AREA MAKER-R  
CENTER MAKER  
COLOR MATRIX  
MENU  
signal or combination of the monitors settings.  
EXIT:MENU ENTER:+ SELECT:  
EXIT:MENU ENTER:+ SELECT:  
<MAIN MENU>  
<MAIN MENU>  
APERTURE CONTROL  
SLOT CONDITION  
sub menu POSITION :LOWER  
COLOR MATRIX  
SLOT CONDITION  
sub menu POSITION :LOWER  
Menu in an item  
Press the  
select or adjust the item.  
or  
buttons to  
Cursor  
Move (select) with the  
or  
buttons.  
EXIT:MENU ENTER:+ SELECT:  
EXIT:MENU ENTER:+ SELECT:  
MAIN MENU when the 4:3 video  
signal is input  
MAIN MENU when the RGB signal  
is input  
HOW TO USE THE SUB  
MENU  
DISPLAYING THE MENU  
The sub menu function applies to Menu Screen items that  
should be adjusted or set while watching the picture. This  
function simplifies the adjustment or setting while watching  
the picture by displaying the single item on the top or bottom  
of the screen.  
SCREENS  
To display MAIN MENU  
Press the  
button on the front panel.  
MENU  
To display SETUP MENU  
To use the sub menu function,  
Press the  
front panel.  
button while pressing the  
button on the  
Press the  
press the  
or  
buttons to select sub menu. Then,  
button to display the sub menu screen.  
To adjust or set an item in the sub menu screen,  
Press the or buttons.  
To change the item to be adjusted or set,  
Press the or buttons.  
To change the position of the sub menu screen,  
Set UPPER(on the top) or LOWER(on the bottom) in  
sub menu POSITIONof MAIN MENU.  
DEGAUSS  
MENU  
VOLUME  
To close the sub menu screen,  
U
N
D
E
R
P
U
L
S
E
C
O
L
O
R
D
E
G
A
U
S
S
S
C
A
N
C
R
O
S
S
O
F
F
A
B
C
D
E
F
M
E
N
U
B
L
U
E
AS  
P
E
C
T
A
R
E
A
INPUT SELECT  
V
O
L
U
M
E
C
H
E
C
K
M
A
R
K
E
R
Press the  
button. The previous Menu Screen is  
displayed.MENU  
Example of sub menu screen  
CONTRAST  
- -  
: 00  
+ +  
<PICTURE SUB ADJ.>  
CLOSING THE MENU  
CONTRAST  
BRIGHT  
:00  
:00  
CHROMA  
:00  
SCREENS  
PHASE  
:00  
NTSC SETUP  
COMPO.LEVEL  
sub menu  
reset  
:00  
:SMPTE  
Using the MENU button  
CONTRAST  
- -  
: 00  
+ +  
Press the  
button a few times until the Menu Screen  
EXIT:MENU ENTER:+ SELECT:  
MENU  
disappears.  
With no operation  
The upper pale screen; when setting  
UPPERin sub menu POSITION”  
The lower dark screen; when setting  
LOWERin sub menu POSITION”  
When approx. 30 seconds have passed since the last Menu  
operation, both screens will disappear.  
* Some items on the Menu Screens disappear automatically  
after setting.  
9
Untitled-1  
9
01.3.27, 9:58  
 
HOW TO USE “MAIN MENU”  
MAIN MENUITEMS  
The following items appear in MAIN MENU.  
Items  
Functions  
Displays  
1
2
3
4
APERTURE CONTROL Compensates the frequency characteristics of the input video signal.  
*1  
SLOT CONDITION  
sub menu POSITION  
AREA MARKER  
Displays the status of the input cards installed in each of the input card slots.  
Selects the display position of the sub menu superimposed on the screen.  
Selects the size marker for the other screen ratio used when the screen  
ratio is 16:9.  
*2  
5
AREA MARKER-R  
Selects the size marker for the other screen ratio used when the screen ratio is  
16:9. (for external control)  
*2  
6
7
CENTER MARKER  
COLOR MATRIX  
Makes the center marker appear or disappear.  
Selects or adjusts the picture color matrix.  
*2  
*1  
About Displays”  
*1: Not displayed when an RGB signal is input.  
*2: Displayed only when the screen ratio is 16:9. Not displayed when an RGB signal is input.  
When some items are not displayed depending on the input signals, subsequent items will move up.  
MAIN MENUSCREENS  
LEVEL  
- -  
:+05  
+ +  
<MAIN MENU>  
<APERTURE CONTROL>  
APERTURE CONTROL  
SLOT CONDITION  
sub menu POSITION :LOWER  
AREA MAKER  
AREA MAKER-R  
CENTER MAKER  
COLOR MATRIX  
LEVEL  
:00  
:HIGH  
CONTROL FREQ.  
sub menu  
reset  
:OFF  
:OFF  
:OFF  
LEVEL  
- -  
:+05  
+ +  
EXIT:MENU ENTER:+ SELECT:  
EXIT:MENU ADJUST:- + SELECT:  
The menu screen when sub  
menuis selected.  
The sub menu screen when  
sub menu POSITIONis set  
to UPPER.  
<SLOT CONDITION>  
INPUT A  
INPUT B  
INPUT C  
INPUT D  
INPUT E  
INPUT F  
: VIDEO-1  
: VIDEO-2  
: COMPO.  
: RGB  
: NO SLOT  
: NO SLOT  
EXIT:MENU  
<COLOR MATRIX>  
<COLOR MATRIX>  
SELECT :MANUAL  
R-Y PHASE :90  
R/B GAIN :0.86  
G-Y PHASE :138  
G/B GAIN :0.36  
sub menu  
SELECT :ITU601  
reset  
R-Y PHASE  
- -  
:+90  
+ +  
EXIT:MENU ADJUST:- + SELECT:  
EXIT:MENU ADJUST:- + SELECT:  
The menu screen when  
MANUALis selected.  
The menu screen when sub  
menuis selected.  
<MAIN MENU>  
<MAIN MENU>  
APERTURE CONTROL  
SLOT CONDITION  
SLOT CONDITION  
sub menu POSITION :LOWER  
sub menu POSITION :LOWER  
COLOR MATRIX  
EXIT:MENU ENTER:+ SELECT:  
EXIT:MENU ENTER:+ SELECT:  
The menu screen when the  
screen ratio is 4:3  
The menu screen when an  
RGB signal is input  
10  
Untitled-1  
10  
01.3.27, 9:58  
 
ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS  
1. APERTURE CONTROL  
Compensates the frequency  
characteristics of the input  
video signal. Press the  
button to display the setting  
menu illustrated on the right.  
NOTE :APERTURE  
3. sub menu POSITION  
Items  
: Selects the display position of the sub menu  
superimposed on the screen.  
<APERTURE CONTROL>  
LEVEL  
:00  
:HIGH  
CONTROL FREQ.  
sub menu  
reset  
Settings : UPPER/LOWER  
Functions : UPPER : An adjustment item is displayed on the  
top of the screen.  
LOWER : An adjustment item is displayed on the  
bottom of the screen.  
EXIT:MENU ADJUST:- + SELECT:  
CONTROL is not  
displayed when the  
RGB signal is input.  
4. AREA MARKER  
Items  
: Selects the size marker for the other screen ratio  
(aspect) used when the screen ratio is 16:9.  
Item  
Adjustment  
range  
: LEVEL  
Settings : OFF/4:3/16:9/14:9/13:9/MODE 1/MODE 2  
Functions : OFF: The marker is not displayed.  
4:3/16:9/14:9/13:9: Displays the marker (a white  
quadrangle) showing the screen size of each  
aspect ratio.  
: 00 ~ +10  
Function  
: Adjusts the compensate value. The higher the  
number is, the larger the compensate value gets.  
Item  
Settings  
Function  
: CONTROL FREQ.  
: HIGH/LOW/OFF  
: Adjusts the frequency compensation.  
HIGH :Compensates the high frequencies.  
LOW :Compensates the low frequencies.  
OFF :Deactivates the aperture compensation.  
MODE 1/MODE 2: Displays no markers because  
these settings will be used for function expansion  
in the future.  
AREA MARKER is displayed when a 16:9 picture such as  
1080i/1035i/720p etc. is displayed or the picture is  
switched to the 16:9 screen ratio by pressing the ASPECT  
button.  
Item  
: sub menu  
To actually display the marker, the AREA MARKER  
button on the monitor needs to be pressed so that it is  
illuminated.  
Adjustment range/  
Settings : Same as LEVEL or CONTROL FREQ.  
Function  
: Performs the LEVEL or CONTROL FREQ.  
settings in a single-line display. The display  
position depends on the sub menu POSITION”  
setting.  
Item  
: reset  
Function  
: Sets the LEVEL and CONTROL FREQ. values to  
factory-preset ones.  
2. SLOT CONDITION  
4:3  
16:9  
Displays the status of the input  
cards installed in each of the  
input card slots. Press the  
button to display the setting  
menu illustrated on the right.  
<SLOT CONDITION>  
INPUT A  
: VIDEO-1  
: VIDEO-2  
: COMPO.  
: RGB  
INPUT B  
INPUT C  
INPUT D  
INPUT E  
INPUT F  
: NO SLOT  
: NO SLOT  
EXIT:MENU  
14:9  
13:9  
Items  
: INPUT A:/INPUT B:/INPUT C:/INPUT D:/INPUT  
E:/INPUT F:  
Settings  
Function  
: VIDEO-1/VIDEO-2/COMPO./RGB/SDI 1/SDI 2/  
NO SLOT  
: Displays the status of the input cards installed in  
each of the input card slots.  
INPUT A/B corresponds to SLOT 1, INPUT C/D to SLOT 2,  
and INPUT E/F to SLOT 3.  
VIDEO-1 or VIDEO-2 shows the video input card is installed.  
COMPO. or RGB shows the component/RGB input card.  
SDI 1 or SDI 2 shows the SDI input card is installed.  
NO SLOT shows no input cards are installed.  
11  
Untitled-1  
11  
01.3.27, 9:58  
 
5. AREA MARKER-R  
R-Y PHASE  
R/B GAIN  
90  
Items  
: Selects the size marker for the other screen ratio  
0.79  
244  
0.45  
90  
(aspect) used when the screen ratio is 16:9. (for  
external control)  
ITU601  
ITU709  
G-Y PHASE  
G/B GAIN  
Settings : OFF/4:3/16:9/14:9/13:9/MODE 1/MODE 2  
Functions : OFF: The marker is not displayed.  
4:3/16:9/14:9/13:9: Displays the marker (a white  
quadrangle) showing the screen size of each  
aspect ratio.  
R-Y PHASE  
R/B GAIN  
0.86  
244  
0.30  
G-Y PHASE  
G/B GAIN  
MODE 1/MODE 2: Displays no markers because  
these settings will be used for function expansion  
in the future.  
AREA MARKER-R is displayed when a 16:9 picture such  
as 1080i/1035i/720p etc. is displayed or the picture is  
switched to the 16:9 screen ratio by pressing the ASPECT  
button.  
The marker is actually displayed when the external control  
selects each setting. (No markers are displayed even if  
each marker is selected only in the monitors AREA  
MARKER-R setting.)  
Item  
Function  
Settings  
: SELECT  
: Selects the picture matrix standard.  
: ITU601 or ITU709/ MANUAL  
ITU601 or ITU709 : Standard setting  
MANUAL : Manual setting  
NOTE :The following items are displayed when MANUAL is  
selected. When ITU601 or ITU709 is selected, they  
are not displayed.  
6. CENTER MARKER  
Item  
Function  
Settings  
: R-Y PHASE  
: Sets the R-Y phase.  
: 90/92/94/112  
Items  
: Makes the center marker appear or disappear.  
Settings : ON/OFF  
Functions : ON : The center marker (a white cross) is  
displayed on the center of the screen.  
OFF : The marker disappears.  
Item  
Function  
Settings  
: R/B GAIN  
: Sets the R/B gain.  
: 0.86/0.56/0.68/0.79  
To actually display the marker, the AREA MARKER  
button on the monitor needs to be pressed so that it is  
illuminated.  
Item  
Function  
Settings  
: G-Y PHASE  
: Sets the G-Y phase.  
: 244/253/236/240  
Item  
: G/B GAIN  
Function  
Settings  
: Sets the G-B gain.  
: 0.30/0.34/0.40/0.45  
Center marker  
Item  
: sub menu  
Function  
: Performs the R-Y PHASE, R/B GAIN, G-Y  
PHASE or G/B GAIN settings in a single-line  
display. The display position depends on the  
sub menu POSITIONsetting.  
: Same as R-Y PHASE, R/B GAIN, G-Y PHASE or  
G/B GAIN  
7. COLOR MATRIX  
Selects or adjusts the  
Settings  
<COLOR MATRIX>  
standard of the color  
demodulation (color  
rendering). Press the  
SELECT :MANUAL  
R-Y PHASE :90  
R/B GAIN :0.86  
G-Y PHASE :244  
G/B GAIN :0.30  
sub menu  
Item  
: reset  
Function  
: Sets the R-Y PHASE, R/B GAIN, G-Y PHASE  
and G/B GAIN values to factory-preset ones.  
button to display the setting  
reset  
menu illustrated on the right.  
EXIT:MENU ADJUST:- + SELECT:  
The menu screen when  
MANUAL is selected.  
The standard setting is set to ITU601or ITU709”  
depending on the input signal format.  
The factory preset of MANUAL is ITU709  
Input Signal Format  
Standard  
setting  
Manual  
setting  
(MANUAL)  
NTSC, PAL, 480/60i,  
480/60p, 576/50i, 575/50p  
ITU601  
ITU709  
ITU709  
720/60p, 1080/50i, 1080/60i,  
1035/60i, 1080/24pSF  
12  
Untitled-1  
12  
01.3.27, 9:58  
 
HOW TO USE “SETUP MENU”  
SETUP MENUITEMS  
Items  
Functions  
1 FUNCTION SETTING  
2 PICTURE SUB ADJ.  
3 COLOR TEMP./BAL.  
4 SIZE/POSI. ADJ.  
5 DISTORTION ADJ.  
6 STATUS DISPLAY  
7 CONTROL LOCK  
8 all reset  
Displays the monitors power-up time or the total usage time.  
Performs approximate adjustments using the control knobs on the front panel.  
Sets or adjusts the color temperature or white balance.  
Adjusts the size or position of the picture.  
Compensates the picture distortion.  
Makes the status of the input signal appear or disappear on the screen.  
Sets the control lock preventing the monitor from misuse.  
Sets all items in SETUP MENU to factory-preset values.  
SETUP MENUSCREENS  
<SETUP MENU>  
<FUNCTION SETTING>  
FUNCTION SETTING  
PICTURE SUB ADJ.  
COLOR TEMP./BAL.  
SIZE/POSI.ADJ.  
DISTORTION ADJ.  
STATUS DISPLAY  
CONTROL LOCK  
COLOR SYSTEM  
RUSH DELAY TIME  
HOUR METER X100h  
:AUTO  
:STD.  
:000  
:ON  
all reset  
EXIT:MENU ENTER:+ SELECT:  
EXIT:MENU ADJUST:- + SELECT:  
<PICTURE SUB ADJ.>  
CONTRAST  
BRIGHT  
:00  
:00  
CHROMA  
:00  
PHASE  
:00  
NTSC SETUP  
COMPO.LEVEL  
sub menu  
reset  
:00  
:SMPTE  
CONTRAST  
- -  
: 00  
+ +  
EXIT:MENU ADJUST:- + SELECT:  
<COLOR TEMP./BAL.>  
COLOR TEMP.  
BLUE DRIVE  
RED DRIVE  
GREEN CUTOFF  
BLUE CUTOFF  
RED CUTOFF  
sub menu  
:LOW  
:000  
:000  
:000  
:000  
:000  
reset  
BLUE DRIVE  
- -  
:000  
+ +  
EXIT:MENU ADJUST:- + SELECT:  
<SIZE/POSI. ADJ.>  
H.SIZE  
H.POSITION  
V.SIZE  
V.POSITION  
sub menu  
reset  
:00  
:00  
:00  
:00  
H.SIZE  
- -  
: 00  
+ +  
EXIT:MENU ADJUST:- + SELECT:  
<DISTORTION ADJ.>  
PINCUSHION  
PIN.BALANCE  
PARALLELOGRAM  
TRAPEZOID  
sub menu  
:00  
:00  
:00  
:00  
reset  
PINCUSHION  
- -  
: 00  
+ +  
EXIT:MENU ADJUST:- + SELECT:  
<STATUS DISPLAY>  
STATUS DISPLAY  
1080/1035  
:ON  
:1080  
Aer you sure ?  
"Yes" then + Key.  
"No" then MENU Key.  
EXIT:MENU ADJUST:- + SELECT:  
13  
Untitled-1  
13  
01.3.27, 9:58  
 
HOW TO USE “SETUP MENU” (cont'd)  
ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS  
1. FUNCTION SETTING  
Item  
Adjustment  
range  
: CONTRAST  
Selects the color system and  
displays the monitors power-  
up time or the total usage time.  
<FUNCTION SETTING>  
: 20 ~ 00 ~ +20  
COLOR SYSTEM  
RUSH DELAY TIME  
HOUR METER X100h  
:AUTO  
:STD.  
:000  
Function  
: For approximate adjustment of the picture  
contrast. Before adjustment, set the CONTRAST  
knob on the front panel to 0.  
Press the  
button to display  
the setting menu illustrated on  
the right.  
EXIT:MENU ADJUST:- + SELECT:  
Item  
: BRIGHT  
Adjustment  
range  
: 20 ~ 00 ~ +20  
Function  
: For approximate adjustment of the picture  
brightness. Before adjustment, set the BRIGHT  
knob on the front panel to 0.  
Item  
Settings  
Function  
: COLOR SYSTEM  
: AUTO/NTSC/PAL  
: Selects the color system when using the video  
input card.  
AUTO : Change NTSC and PAL automatically.  
NTSC : Keeps the color system NTSC.  
PAL : Keeps the color system PAL.  
Item  
Adjustment  
range  
: CHROMA  
: 20 ~ 00 ~ +20  
Function  
: For approximate adjustment of the color density.  
Before adjustment, set the CHROMA knob on  
the front panel to 0.  
NOTE :Normally select AUTO. However, if the input signal is  
unstable, select NTSC or PAL.  
Item  
Settings  
Function  
: RUSH DELAY TIME  
: STD./SLOW  
Item  
Adjustment  
range  
: PHASE  
: Sets the time when the power supply to the  
monitors circuits (excluding the micro computers)  
starts after the power switch is pressed.  
STD. : The power supply starts approx.  
1 second after the power switch is  
pressed.  
: 20 ~ 00 ~ +20  
Function  
: For approximate adjustment of the picture hue.  
Before adjustment, set the PHASE knob on the  
front panel to 0.  
Item  
: NTSC SETUP  
SLOW : The power supply starts approx.  
3.2 seconds after the power switch is  
pressed.  
Settings  
Function  
: 00/7.5  
: Sets the level of the input NTSC signal.  
00 : Compliant with 0% set-up signal.  
75 : Compliant with 7.5% set-up signal.  
NOTE :When turning on many multi-format monitors  
simultaneously, it is recommended to use SLOW to  
control rush current.  
NOTE :NTSC SETUP is displayed only when the video input  
card is installed and an NTSC signal is input.  
Item  
: HOUR METER X100h  
Item  
: COMPO. LEVEL  
Number  
range  
Function  
Settings  
Function  
: SMPTE/B75/B00  
: Sets the level of the input component signal.  
SMPTE :Compliant with M2VTR signals.  
: 000 ~ 655  
: Displays the total usage time of the monitor in  
hundred-hour units.  
B75  
:Compliant with Betacam 7.5% set-up  
signal.  
When the timer passes 655, it returns to 000.  
The timer does not count the usage time under one hour.  
B00  
:Compliant with Betacam 0% set-up  
signal.  
NOTE :COMPO. LEVEL is displayed only when a 480/60i,  
480/60p, 576/50i or 576/50p signal is input.  
2. PICTURE SUB ADJ.  
Performs approximate  
adjustments using the control  
knobs on the front panel. Press  
the button to display the  
setting menu illustrated on the  
right.  
Item  
: sub menu  
<PICTURE SUB ADJ.>  
Adjustment range/  
Settings : Same as CONTRAST, BRIGHT, CHROMA,  
PHASE and COMPO LEVEL/NTSC SETUP.  
CONTRAST  
BRIGHT  
:00  
:00  
CHROMA  
:00  
PHASE  
:00  
NTSC SETUP  
COMPO.LEVEL  
sub menu  
reset  
:00  
:SMPTE  
Function  
: Performs CONTRAST, BRIGHT, CHROMA,  
PHASE or COMPO LEVEL/NTSC SETUP  
settings in a single-line display. The sub menu  
display varies depending on the selected item.  
EXIT:MENU ADJUST:- + SELECT:  
NOTE : When the RGB signal  
is input, only  
CONTRAST and  
Item  
Function  
: reset  
BRIGHT are displayed. When the PAL signal is  
input, only CONTRAST, BRIGHT and CHROMA are  
displayed.  
: Sets the CONTRAST, BRIGHT, CHROMA,  
PHASE and COMPO LEVEL/NTSC SETUP  
values to factory-preset ones.  
14  
Untitled-1  
14  
01.3.27, 9:58  
 
3. COLOR TEMP./BAL.  
Sets or adjusts the color  
temperature or white balance.  
4. SIZE/POSI. ADJ.  
Adjusts the size or position of  
the picture. Press the  
button to display the setting  
menu illustrated on the right.  
<COLOR TEMP./BAL.>  
<SIZE/POSI. ADJ.>  
COLOR TEMP.  
:LOW  
:000  
:000  
:000  
:000  
:000  
H.SIZE  
:00  
:00  
:00  
:00  
Press the  
button to display  
BLUE DRIVE  
RED DRIVE  
GREEN CUTOFF  
BLUE CUTOFF  
RED CUTOFF  
sub menu  
H.POSITION  
V.SIZE  
the setting menu illustrated on  
the right.  
V.POSITION  
sub menu  
reset  
reset  
EXIT:MENU ADJUST:- + SELECT:  
EXIT:MENU ADJUST:- + SELECT:  
Item  
Settings  
Function  
: COLOR TEMP.  
: HIGH/LOW  
: Selects the color temperature.  
Item  
Adjustment  
range  
: H.SIZE  
: 20 ~ 00 ~ +20  
HIGH : Sets the color temperature to D9300.  
LOW : Sets the color temperature to D6500.  
Function  
: Adjusts the horzitontal screen size.  
: Reduces the screen size horizontally.  
+ : Enlarges the screen size horizontally.  
Item  
: BLUE DRIVE  
Item  
Adjustment  
range  
: H.POSITION  
Adjustment  
range  
Function  
: MIN ~ 000 ~ MAX (in 127 grades)  
: Adjusts the blue drive level.  
: 20 ~ 00 ~ +20  
Function  
: Adjusts the horzitontal screen position.  
: Move the screen to the left.  
+ : Move the screen to the right.  
Item  
Adjustment  
range  
: RED DRIVE  
: MIN ~ 000 ~ MAX (in 127 grades)  
: Adjusts the red drive level.  
Item  
: V.SIZE  
Function  
Adjustment  
range  
Function  
Item  
Adjustment  
range  
: GREEN CUTOFF  
: 20 ~ 00 ~ +20  
: Adjusts the vertical screen size.  
: Reduces the screen size vertically.  
+ : Enlarges the screen size vertically.  
: MIN ~ 000 ~ MAX (in 205 grades)  
: Sets the green cut-off point.  
Function  
Item  
Adjustment  
range  
: BLUE CUTOFF  
Item  
Adjustment  
range  
: V.POSITION  
: MIN ~ 000 ~ MAX (in 205 grades)  
: Sets the blue cut-off point.  
: 20 ~ 00 ~ +20  
Function  
Function  
: Adjusts the vertical screen position.  
: Move the screen up.  
+ : Move the screen down.  
Item  
Adjustment  
range  
: RED CUTOFF  
: MIN ~ 000 ~ MAX (in 205 grades)  
: Sets the red cut-off point.  
Item  
: sub menu  
Function  
Adjustment range/  
Settings : Same as H.SIZE, H.POSITION, V.SIZE and  
V.POSITION.  
Item  
: sub menu  
Adjustment range/  
Settings : Same as BLUE DRIVE, RED DRIVE, GREEN  
CUTOFF, BLUE CUTOFF and RED CUTOFF.  
Function  
: Performs H.SIZE, H.POSITION, V.SIZE or  
V.POSITION settings in a single-line display. The  
sub menu display varies depending on the  
selected item.  
Function  
: Performs BLUE DRIVE, RED DRIVE, GREEN  
CUTOFF, BLUE CUTOFF or RED CUTOFF  
settings in a single-line display. The sub menu  
display varies depending on the selected item.  
Item  
: reset  
Function  
: Sets the H.SIZE, H.POSITION, V.SIZE and  
V.POSITION values to factory-preset ones.  
Item  
: reset  
Function  
: Sets the BLUE DRIVE, RED DRIVE, GREEN  
CUTOFF, BLUE CUTOFF and RED CUTOFF  
values to factory-preset ones.  
15  
Untitled-1  
15  
01.3.27, 9:58  
 
5. DISTORTION ADJ.  
6. STATUS DISPLAY  
Compensates the picture  
Makes the status of the input  
signal appear or disappear on  
the screen. Press the  
button to display the setting  
menu illustrated on the right.  
<STATUS DISPLAY>  
<DISTORTION ADJ.>  
distortion. Press the  
to display the setting menu  
illustrated on the right.  
button  
STATUS DISPLAY  
1080/1035  
:ON  
:1080  
PINCUSHION  
:00  
:00  
:00  
:00  
PIN.BALANCE  
PARALLELOGRAM  
TRAPEZOID  
sub menu  
reset  
EXIT:MENU ADJUST:- + SELECT:  
EXIT:MENU ADJUST:- + SELECT:  
Item  
Settings  
Function  
: STATUS DISPLAY  
: ON/OFF  
: Makes the format name appear or disappear  
when signals are input and the signal status  
appear or disappear when the input signal is  
changed.  
Item  
Adjustment  
range  
: PINCUSHION  
: 20 ~ 00 ~ +20  
Function  
: Compensates pincushion picture distortion.  
: Expands both left and right sides of the  
picture.  
ON : The information is displayed.  
OFF : The information is not displayed.  
+ : Squeezes both left and right sides of the  
picture.  
Item  
: 1080/1035  
Item  
: PIN.BALANCE  
Settings  
Function  
: 1080/1035  
Adjustment  
range  
Function  
: Makes the number of effective scanning lines  
appear or disappear when the HDTV signal is  
input.  
: 20 ~ 00 ~ +20  
: Adjusts the compensation balance of the  
pincushion picture distortion.  
1080 :Sets the number to 1080. (Select when  
the digital HDTV signal is input.)  
1035 :Sets the number to 1035. (Select when  
the analog HDTV signal is input.)  
: The picture is expanded on the left side, and  
squeezed on the right side.  
+ : The picture is squeezed on the left side, and  
expanded on the right side.  
Item  
: PARALLELOGRAM  
Adjustment  
range  
Function  
7. CONTROL LOCK  
: 20 ~ 00 ~ +20  
: Compensates parallelogram picture  
distortion.  
Item  
: CONTROL LOCK  
Settings : OFF/ON  
Function : Invalidates most of operations on the front panel  
(including menu screen operations).  
OFF : Enables normal operations.  
: Moves the upper side of the picture to the  
right, and the lower side to the left.  
+ : Moves the upper side of the picture to the left,  
and the lower side to the right.  
ON : Invalidates all operations except the power  
switch and CONTROL LOCK.  
NOTE: While CONTROL LOCK is set to ON, attempting to  
perform any operation except power switch and  
Item  
Adjustment  
range  
: TRAPEZOID  
CONTROL LOCK causes the “  
Control lock on!”  
: 20 ~ 00 ~ +20  
warning to appear on the screen for approx. 3  
seconds. (It is possible to operate the power switch  
and display SETUP MENU.)  
Function  
: Compensates trapezoid picture distortion.  
: Enlarges the upper side of the picture.  
+ : Reduces the upper side of the picture.  
When SETUP MENU is displayed while CONTROL  
LOCK is set to ON, the cursor (4) is located next to  
CONTROL LOCK and cannot be moved.  
Item  
: sub menu  
Adjustment range/  
Settings : Same as PINCUSHION, PIN.BALANCE,  
PARALLELOGRAM and TRAPEZOID.  
8. all reset  
Function  
: Performs PINCUSHION, PIN.BALANCE,  
PARALLELOGRAM or TRAPEZOID settings in a  
single-line display. The sub menu display varies  
depending on the selected item.  
Function : Sets all items in SETUP MENU to factory-preset  
values.  
Item  
: reset  
Function  
: Sets the PINCUSHION, PIN.BALANCE,  
PARALLELOGRAM and TRAPEZOID values to  
factory-preset ones.  
16  
Untitled-1  
16  
01.3.27, 9:58  
 
HOW TO USE EXTERNAL  
CONTROL  
ABOUT EXTERNAL CONTROL  
This multi-format monitor has two external control terminals. One is the MAKE terminal, which controls the monitor by connecting  
the terminals with many functions to the ground (GND) terminal. The other is the RS-232C terminal, which allows the monitor to  
be controlled by a PC via serial communication.  
Control priority is in the following order; the MAKE terminal > the RS-232C terminal > the buttons on the front panel.  
HOW TO USE THE MAKE TERMINAL  
10  
9
8
7
6
5 4 3 2 1  
Connections  
Connect (short-circuit) the 15th terminal (GND) to each of the 1st through 14th terminals in the  
3-lines 15-pins D-sub connector. The functions of each terminal are listed below.  
15 14 13 12 11  
The Names and Functions of Terminals  
No. Names  
Functions  
Operations (OFF p[ ON)  
*1  
1
TALLY  
Puts on the tally lamp.  
Put on  
Put off  
2
INPUT A  
Changes the input to INPUT A  
Changes the input to INPUT B  
Changes the input to INPUT C  
Changes the input to INPUT D  
Changes the input to INPUT E  
Changes the input to INPUT F  
Not change  
Not change  
Not change  
Not change  
Not change  
Not change  
Change  
Change  
Change  
Change  
Change  
Change  
Change  
Display  
16:9  
3
INPUT B  
4
INPUT C  
5
INPUT D  
6
INPUT E  
7
INPUT F  
8
COLOR OFF  
AREA MARKER  
ASPECT  
Changes the picture black-and-white. Not change  
9
Displays the area marker.  
Not display  
4:3  
10  
11  
12  
Changes the screen ratio to 16:9  
Makes the screen under-scan  
Selects the type of the area marker  
UNDER SCAN  
MARKER  
Over-scan  
Under-scan  
Selection in the main unit Selection in the remote  
control  
*2  
13  
14  
STATUS  
Displays the monitors status  
Display  
*3  
REMOTE ENABLE Makes the external control form the  
MAKE terminal valid or invalid  
Invalid  
Valid  
*4  
15  
GND  
Used as a ground terminal  
*1 : OFF stands for disconnection, and ON stands for short-circuit.  
*2 : Selects the area marker size from AREA MARKER (setting on the main unit) or AREA MARKER-R (setting on the remote control) setting.  
*3 : The STATUS function is activated when the connection to the STATUS terminal is changed (ON to OFF, or OFF to ON). The monitors status  
is displayed for 3 seconds.  
*4 : Setting REMOTE ENABLE to ON enables remote control from the MAKE terminal.  
Operation  
1. Set REMOTE ENABLE to ON.  
2. Short-circuit or disconnect the desired terminal.  
Changing the Signal Input.  
Changing the Signal Input  
1. Set REMOTE ENABLE to ON.  
2. Short-circuit the desired INPUT terminal.  
3. Disconnect the INPUT terminal selected above. The signal input is actually changed after the disconnection has been  
completed.  
NOTE : When more than two terminals are selected (short-circuited) from INPUT A through INPUT F, the signal input is not  
changed.  
To control INPUT A through INPUT F, we recommend using the interlock switch, which turns off a switch when another  
switch is turned on.  
17  
Untitled-1  
17  
01.3.27, 9:58  
 
HOW TO USE EXTERNAL  
CONTROL (cont.)  
HOW TO USE THE RS-232C TERMINAL  
You can control the monitor from your PC via the RS-232C terminal.  
For details on operating the monitor from the PC, consult your dealer or service center for details.  
5
4
3
2
1
9
8
7
1. Cable  
Prepare a straight cable with a D-sub connector (9-pin, female) and a D-sub  
connector (9-pin, male)  
6
2. Communications Specifications  
Baud Rate : 4800/9600/19200 (factory pre-set; 4800)  
Pin No.  
Signal  
Data Bits  
Parity  
Stop Bits  
: 8 bits  
: No parity  
: 1  
1
2
3
4
5
6
7
8
9
DCD (Data Carrier Detect)  
RD (Recive Data)  
Flow Control : Hardware (RTS/CTS)  
TD (Transmit Data)  
DTR (Data Terminal Ready)  
GND (Ground)  
3. Commands  
Format  
DSR (Data Set Ready)  
RTS (Request To Send)  
CTS (Clear To Send)  
RI (Ring Indication)  
Header  
ID  
Command  
Data  
CR  
Header  
!
?
@
Control from the PC to the monitor  
Reference from the PC to the monitor  
Answer from the monitor to the PC  
ID + Command + Data  
B
D
S
Basic command  
Characters  
00 ~ 07  
00 ~ 05  
00 ~ 0E  
00 ~ 07  
00 ~ 05  
00 ~ 01  
00, 01 or No data  
20 ~ +20  
Command for adjusting the picture size  
Command for adjusting the picture quality  
Command for selecting the menu item  
Command for selecting the menu item  
Command for adjusting the white balance  
Command for inquiring for the monitors status  
20 ~ +20  
M
F
00, 01, 10, 11  
00, 01  
W
C
256 ~ +255  
0 ~ 655 or No data  
During Communication from the PC to the Monitor  
The monitor receives the data when DSR remains ON (high) and CTS is set to ON.  
During Communication from the Monitor to the PC  
The monitor sends the data when both DSR and DCD are set to ON and RTS is set to ON.  
Communication Procedures  
The following is the communication procedures.  
1. Starting the communication  
Receives the connection command (!BCN1Cr) from the PC [ Sends the monitors status (@BOKCr) to the PC  
2. Performing the external control  
Receives the control command (!XXXXCr) from the PC [ Sends the monitors status (@BOKCr) to the PC  
* The monitor repeats these receiving and sending if necessary.  
3. Terminating the communication  
Receives the termination command (!BCN0Cr) [ Sends the monitors status (@BOKCr) to the PC  
* After sending the data to the monitor, the PC must first receive the data from the monitor and then send the next command  
because the communication is performed in a hand-shake system. If the PC does not receive the status from the monitor after  
sending the command, re-send the command.  
18  
Untitled-1  
18  
01.3.27, 9:58  
 
TROUBLESHOOTING  
Solutions to common problems related to your monitor are described here. If none of the solutions presented here solve  
the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance.  
Reference  
pages  
Problems  
Points to be checked  
Measures (Remedy)  
Firmly insert the power plug.  
No power supply  
Is the power plug loosened or  
disconnected?  
5
No picture with  
the power on  
Is the signal cable disconnected?  
Connect the signal cable firmly.  
6, 7  
Is the power of the connected  
component ON?  
Turn on the power of the connected component  
and set it correctly.  
Is the signal output from the connected  
component?  
Is the input signal selected correctly?  
Select the correct input with the INPUT SELECT  
buttons.  
5, 8  
Is the input signal adapted to the  
monitors specification?  
Check that the input signal format corresponds to  
the installed input card format.  
6, 7  
6, 7  
No sound  
Is the audio cable disconnected?  
Connect the audio cable firmly.  
Is the audio signal output from the  
connected component?  
Set the connected component correctly.  
Is the volume output set to minimum?  
Adjust the speaker volume with the VOLUME  
+/buttons.  
4
Wrong color  
Has the picture adjustment been  
changed?  
Set each picture adjustment knob to the standard  
(centered) position. Or, set each picture  
adjustment item in [ PICTURE SUB ADJ.] in the  
<SET UP MENU> screen to Standard (00) (or  
use the [reset] function).  
9, 14  
Has the WHITE BALANCE setting  
been changed?  
Set each [COLOR TEMP./BAL.] item in the  
<SET-UP MENU> screen to Standard (000) (or  
use the [reset] function).  
15  
6
Are any cables connected to the  
component/RGB input card?  
Connect each signal cable firmly.  
Has the correct signal been input to the Select INPUT A/C when the component signal is  
component/RGB input card and the  
correct INPUT been selected on the  
monitor?  
input, or select INPUT B/D/F when the RGB  
signal is input.  
6
Unnatural picture  
Shaking picture  
Has [CONTRAST] or [BRIGHT] been  
changed?  
Adjust the CONTRAST or BRIGHT picture  
adjustment knobs.  
Or, adjust the [CONTRAST] or [BRIGHT] item in  
[PICTURE SUB ADJ.] in the <SET-UP MENU>  
screen.  
14  
Move the monitor away from the device until the  
picture stops shaking.  
Connect the power plug to another AC outlet  
away from the former one.  
Is the monitor close to a motor,  
transformer or any other device  
generating a strong magnetic field?  
(a fan, fluorescent light, laser printer,  
another monitor, etc.)  
19  
Untitled-1  
19  
01.3.27, 9:58  
 
TROUBLESHOOTING (cont.)  
Reference  
pages  
Problems  
Points to be checked  
Measures (Remedy)  
Irregular color  
Is the monitor placed or moved close to Move the device away from the monitor.  
Press the DEGAUSS button on the front panel to  
degauss the screen.  
a speaker or any other device  
incorporating a magnet?  
4
When degaussing, wait more than 30 minutes for  
maximum effect.  
Has the position of the monitor been  
changed with the power on?  
Wrong picture  
position, wrong  
picture size  
Has the picture position, size or  
distortion been changed?  
Adjust the picture size (H SIZE, V SIZE) or  
position (H. POSITION, V. POSITION) in the  
[SIZE/POSI. ADJ.] item in the <SETUP MENU>  
screen.  
Adjust the picture distortion (PINCUSHION, PIN.  
BALANCE, TRAPEZOID and PARALLELOGRAM)  
in the [DISTORTION ADJ.] item in the <SETUP  
MENU> screen.  
15, 16  
It may not be possible to expand the picture due  
to the selected input mode. In this case,  
adjustment is impossible.  
Have the UNDER SCAN or ASPECT  
button been pressed?  
When the UNDER SCAN or ASPECT button is  
lit, press each button to invalidate each setting.  
4
Front panel  
buttons and  
knobs do not  
function  
Has the CONTROL LOCK function  
been set to ON?  
Set the CONTROL LOCK function to OFF.  
16  
Has the monitors setting been  
changed to enable control from an  
external unit via the REMOTE  
terminals?  
Change the setting of the external control to  
control the monitor locally.  
17, 18  
The following are not malfunctions:  
You may see two horizontal lines on the monitor. They are  
the shadows of the damper linesthat are necessary for  
composing the monitor. These lines are not a malfunction.  
When a bright still image (such as a white cloth) is  
displayed for a long period, it may appear to be colored.  
This is due to the structure of the cathode ray tube and  
will disappear when another image is displayed.  
You may sometimes experience a mild electric shock  
when you touch the picture tube. This phenomenon is due  
to a normal buildup of static electricity on the CRT and is  
not harmful.  
The monitor emits a strange sound when the room  
temperature changes suddenly. This is only a problem if  
an abnormality appears on the screen as well.  
If two or more monitors are operated next to each other,  
their images may shake or be distorted. This phenomenon  
is due to mutual interference; it is not a malfunction. Move  
the monitors away from each other until the interference  
disappears or turn the power off on any monitor that is not  
being used.  
Damper line  
UNDER  
SCAN  
PULSE  
CROSS  
COLOR  
OFF  
DEGAUSS  
MENU  
POWER  
SLOT 1  
SLOT 2  
SLOT 3  
A
B
C
D
E
F
BLUE  
ASPECT  
AREA  
INPUT SELECT  
VOLUME  
CHECK  
MARKER  
20  
Untitled-1  
20  
01.3.27, 9:58  
 
SPECIFICATIONS  
Type  
: Multi-format monitor  
Picture Tube : 17" measured diagonally  
Effective  
Remote Inputs : Point-of-contact connection, 1 line,  
D-sub connector (15-pin 3-line)  
Serial connection, 1 line, D-sub connector  
(9-pin), compliant to RS-232C  
Screen Size : Width  
: 13" (330 mm)  
Height : 9-7/8" (250 mm)  
Diagonal : 16-1/4" (410 mm)  
Audio Output : 1 W (monaural)  
Built-in  
Scanning  
Speaker  
: 3-1/8" (8 cm) round x 1  
Frequency  
: H : 15 kHz/15 kHz 45 kHz  
Environmental  
V : 50 Hz 100 Hz  
Video Band : Component : 25 MHz (3 dB)  
Video (Y/C) : 8 MHz (3 dB)  
Conditions : Operating temperature : 5°C 35°C  
(41°F 95°F)  
Operating humidity  
: 20% 80%  
Horizontal  
(non-condensing)  
Resolution : Video (Y/C) : 600 TV lines  
Power  
1080/60i  
: 800 TV lines  
Requirements : 120 V AC, 50 Hz/60 Hz  
Input  
Power  
Terminals  
: Installing an optional input card in SLOT 1,  
2, or 3 is required.  
Consumption : 1.56 A (not including input card)  
Max. 1.85 A (including input card)  
INPUT A/INPUT B: Terminals on the input  
card in SLOT 1  
Dimensions : Width : 15-5/8" (395 mm)  
Height : 13-1/4" (334 mm)  
INPUT C/INPUT D: Terminals on the input  
card in SLOT 2  
Depth : 18-3/8" (466.5 mm)  
(not including wide mask and input card)  
INPUT E/INPUT F: Terminals on the input  
card in SLOT 3  
Weight  
: 51.0 lbs (23.2 kg)  
(not including wide mask and input card)  
Compliant  
Accessory  
: AC power cord [7.9 ft (2.4 m)] x 1  
Video Signal : NTSC/PAL (using the IF-C01PNG)  
480i/576i/480p/1080i (60 HZ/24pSF)/720p  
(using the IF-C01COMG)  
D1 serial digital (using the IF-C01SDG)  
[Dimensions]  
Unit : inch (mm)  
<Front View>  
15-5/8" (395)  
* Illustrations and pictures used in this manual have been  
exaggerated, abbreviated or compounded for explanatory purposes  
only. The appearance of the actual product may differ slightly.  
* Dimensions and weight are approximate.  
* E. & O.E. Design and specifications subject to change without  
notice.  
13-1/4" (336)  
UNDER  
SCAN  
PULSE  
CROSS  
COLOR  
OFF  
DEGAUSS  
MENU  
POWER  
SLOT 1  
SLOT 2  
SLOT 3  
A
B
C
D
E
F
BLUE  
ASPECT  
AREA  
INPUT SELECT  
VOLUME  
CHECK  
MARKER  
11-3/8" (288)  
<Side View>  
<Front View with the wide mask attached>  
18-3/8" (466.5)  
13-1/8" (331)  
UNDER  
SCAN  
PULSE  
CROSS  
COLOR  
OFF  
DEGAUSS  
MENU  
POWER  
SLOT 1  
SLOT 2  
SLOT 3  
A
B
C
D
E
F
BLUE  
ASPECT  
AREA  
INPUT SELECT  
VOLUME  
CHECK  
MARKER  
11-3/8" (286)  
2-3/4"  
(68)  
21  
Untitled-1  
21  
01.3.27, 9:58  
 
Compliant Signal Formats of Each Input Card  
Input Signals  
NTSC  
IF-C01PNG  
IF-C01COMG  
IF-C01SDG  
R
R
R
R
R
R
R
R
R
R
PAL  
Black-and-White (50 Hz/60 Hz)  
480/60i (525i)  
480/60p (525p)  
576/50i (*1)  
576/50p (*1)  
720/60p (720p)  
1080/50i  
1080/60i (1125i)  
1035/60i (1125i)  
1080/24pSF  
R : Input possible. Pre-set.  
: Input possible. Not pre-set. Any adjustments required in some cases.  
: Input impossible  
*1 : 576/50i and 576/50p are not pre-set. When these signals are input, some adjustments are required.  
22  
Untitled-1  
22  
01.3.27, 9:58  
 
SPECIFICATIONS (INPUT CARD: OPTIONAL)  
IF-C01COMG: COMPONENT/RGB INPUT CARD  
Type  
: Component/RGB input card for multi-format monitor  
Inputs/Outputs : Component (Y, PB/B-Y, PR/R-Y) or RGB: 1 line, BNC connector x 6  
Synchronised signal (HD/CS, VD) : 1 line, BNC connector x 4  
* The input (IN) and output (OUT) terminals are bridge-connected. Auto termination.  
Audio signal : 1 line (monaural), RCA pin x 2  
* The input (IN) and output (OUT) terminals are bridge-connected.  
Required slots : 1  
Power  
consumption : 14 V DC, 0.02 A  
Weight  
: 0.5 kg (1.1 lbs.)  
Dimensions  
(W x H x D)  
: 43 mm x 154.5 mm x 191.9 mm  
(1-3/4" x 6-1/8" x 7-5/8")  
IF-C01PNG: VIDEO INPUT CARD  
Type  
: Video input card for multi-format monitor  
Inputs/Outputs : VIDEO 1/VIDEO 2: 2 lines, BNC connector x 4  
Synchronised signal (EXT.SYNC): 1 line, BNC connector x 2  
* The input (IN) and output (OUT) terminals are bridge-connected. Auto termination.  
Y/C signal : 1 line, input only, mini-DIN 4-pin connector x 1 (Y/C input has a priority to a  
VIDEO 2 input)  
Audio signal : 2 lines (monaural), RCA pin x 4  
* The input (IN) and output (OUT) terminals are bridge-connected.  
Required slots : 1  
Power  
consumption : 14 V DC, 0.25 A  
7 V DC, 0.15 A  
Weight  
: 0.5 kg (1.1 lbs.)  
Dimensions  
(W x H x D)  
: 43 mm x 154.5 mm x 191.9 mm  
(1-3/4" x 6-1/8" x 7-5/8")  
IF-C01SDG: SDI INPUT CARD  
Type  
: SDI input card for multi-format monitor  
Inputs/Outputs : Digital input (SDI 1/SDI 2): 2 lines, BNC connector x 2  
Digital output (SWITCHED OUT): 1 line, BNC connector x 1  
Audio signal: 2 lines (monaural), RCA pin x 4  
* The input (IN) and output (OUT) terminals are bridge-connected.  
Format  
: D1 serial component digital, 525/625 auto switching (compliant to SMPTE259M)  
Required slots : 1  
Power  
consumption : 7 V DC, 0.65 A  
Weight  
: 0.5 kg (1.1 lbs.)  
Dimensions  
(W x H x D)  
: 43 mm x 154.5 mm x 191.9 mm  
(1-3/4" x 6-1/8" x 7-5/8")  
23  
Untitled-1  
23  
01.3.27, 9:58  
 
APPENDIX: CONNECTION EXAMPLES FOR  
THE SDI INPUT CARD  
This section explains the usage precautions and connection examples when using the SWITCHED OUT terminal of the SDI input  
card.  
Usage Precautions  
The selected signal is output from the SWITCHED OUT terminal only when the monitors power is turned on.  
The output signal from the SWITCHED OUT terminal is the one that is selected from the signals input to SDI 1 or SDI 2.  
The table below shows the connection between the INPUT SELECT buttons (input signal selection) and the input/output of  
the SDI input card.  
Selected INPUT SELECT Buttons  
Signal Output from the SWITCHED OUT Terminal  
Signal from SDI 1  
A, C, E  
B, D, F  
Signal from SDI 2  
JVC PROFESSIONAL PRODUCTS COMPANY  
DIVISION OF US JVC CORP.  
1700 Valley Road Wayne, N.J. 07470  
JVC CANADA INC.  
21 Finchdene Square, Scarborough Ontario M1X 1A7  
Printed in Japan  
LCT0971-001A  
0201-I-U-VP  
2001 VICTOR COMPANY OF JAPAN, LIMITED  
©
Untitled-1  
24  
01.3.27, 9:58  
 

Indesit Refrigerator CA 55 User Manual
Intex Recreation Swimming Pool Heater HT30220 User Manual
iOptron Telescope 8405 User Manual
JBL Speaker S310II User Manual
Jenn Air Refrigerator JCD2292KTB User Manual
JVC CD Player XL SV23GD User Manual
JVC Speaker System MX KB1 MX KB2 User Manual
Kambrook Oven KOT600 User Manual
Kenmore Washer 3950144 User Manual
Kenwood Stereo Amplifier KAC 821 User Manual