JVC CRT Television C T1421 User Manual

SPECIFICATIONS  
Model  
C-T1421  
C-T2021  
AC Power Input:  
110V-240V 50Hz/60Hz (Rating), 100V-260V 50Hz/60Hz (Operating)  
AC Power Consumption:  
TV Color System:  
Picture Tube:  
44 Watts  
70 Watts  
PAL-M, PAL-N, NTSC-M  
33.6 cm (measured diagonally)  
48 cm (measured diagonally)  
Audio Power Output Rating: 0.75+0.75 Watts (monaural)  
1.5 + 1.5. Watts (monaural)  
For models:  
C-T1421  
Speaker:  
Input:  
10.8 cm x 4.5 cm Full Range, 8 ohm x 2  
10.8 cm x 4.5 cm Full Range, 4 ohm x 2  
Video: 1.0Vp-p 75 ohm  
Audio: 300 mV, 47K ohm  
3.5 mm ø x 1  
EARPHONE jack:  
Tuner Type:  
C-T2021  
COLOR TELEVISION  
USER'S GUIDE  
181 Channel, Quartz PLL Frequency Synthesized  
Infrared, Direct Access, 2 x AAA batteries  
Remote Control:  
Receiving Channels:  
VHF  
2-13  
UHF  
CATV  
14-69  
01-97 (5A)-(A-3)  
98-99 (A-2)-(A-1)  
14-22 (A)-(I)  
23-36 (J)-(W)  
37-65 (AA)-(FFF)  
66-125 (GGG)-(125)  
Antenna Input Impedance:  
75 Ohm (VHF/UHF/CATV) Coaxial Input  
Dimensions:  
Weight:  
46 cm (W) x 36.3 cm (D) x 31.8 cm (H) 60 cm (W) x 48 cm (D) x 44.6 cm (H)  
9.5 kg  
17.5 kg  
ACCESSORIES:  
Remote Control  
AAA Batteries x 2  
300-75 ohm Matching Transformer  
Telescopic Antenna (C-T1421 only)  
Specifications are subject to change without notice.  
POWER  
1
4
7
0
2
5
3
6
9
8
QUICK VIEW  
CALL  
SLEEP  
MUTING  
CH  
VOL  
VOL  
MENU  
ENTER  
CH  
SET  
+
RESET  
POWER  
VIDEO  
AV2 IN  
AUDIO  
EARPHONE  
VOLUME  
+
CHANNEL  
+
TV/CAP/  
TEXT  
STAND BY ON TIMER  
TV/VCR  
CH. 1/2  
SET  
+
ENTER  
RESET  
ON/  
OFF  
MENU  
VICTOR COMPANY OF JAPAN LIMITED  
IMPORTANT NOTE TO THE CUSTOMER:  
In the space below, enter the serial number for your  
television (located on the rear of the television cabinet).  
Staple your sales receipt or invoice to the inside cover of this guide.  
Keep this user's guide in a convenient place for future reference.  
Keep the carton and original packaging for future use.  
Serial Number  
 
REMOTE CONTROL  
FEATURES  
181 Channel Tuner - The tuning system is capable of receiving all 68 VHF/UHF standard broadcast channels that are  
available in your area. When operating on a cable system, it can tune to the standard VHF channel frequencies plus  
up to 113 cable channel frequencies. The actual number of channels received depends upon channel reception in  
your area or your cable system.  
On-Screen 3 Language Display - This TV can display the on screen language in English, Spanish or Portuguese.  
ON/OFF Timer - Allows you to automatically turn on or off your TV at a set time.  
Sleep Timer - Operable from the remote control, this TV can be programmed up to 120 minutes to turn off  
automatically.  
Picture Control Adjustments - The On-Screen display allows precise remote control adjustment of  
BRIGHTNESS, COLOR, CONTRAST, SHARPNESS, TINT.  
Closed Captioned Decoder - Displays text captions or 1/2 of full screen text on the screen for hearing impaired  
viewers.  
POWER  
1
1
2
5
3
6
9
2
4
7
0
8
10  
3
4
QUICK VIEW  
CALL  
Front Video Input Jacks - A VCR or other video device may be hooked up.  
Auto Voltage - This TV can be used from a household 110V-240V, 50/60Hz.  
SLEEP  
MUTING  
11  
12  
CH  
VOL  
VOL  
5
LOCATION OF CONTROLS  
FRONT  
BACK  
MENU  
ENTER  
CH  
SET  
6
7
+
13  
14  
15  
RESET  
8
9
TV/CAP/  
TEXT  
TV/AV  
CH. 1/2  
A
V1 IN  
POWER  
VIDEO  
AV2 IN  
AUDIO  
EARPHONE  
VOLUME  
+
CHANNEL  
+
VIDEO  
AUDIO  
STAND BY ON TIMER  
SET  
+
ENTER  
RESET  
ON/  
OFF  
MENU  
9
10 11  
1. POWER Button - Press to turn the TV on or off when  
the TV is standby mode.  
2. 10-key pad - Allows direct access to any channel.  
3. QUICK VIEW Button - Switches between the present  
channel and the last channel selected.  
8. RESET- Button - Press to reset the On-Screen picture  
adjustments, clock setting and ON/OFF timer setting.  
9. TV/AV Button - Switches between the TV and external  
input sources.  
10. CALL - Displays the current status time, channel (or  
Input), the present settings on the TV screen.  
11. MUTING Button - Press to turn off the sound. Press  
again to turn the sound back on.  
POWER  
VIDEO  
AV2 IN  
AUDIO  
EARPHONE  
VOLUME  
+
CHANNEL  
+
STAND BY ON TIMER  
SET  
+
ENTER  
RESET  
ON/  
OFF  
MENU  
4. SLEEP TIMER Button - Sets the TV to turn off auto-  
matically after up to 120 minutes.  
1
2
3
4
5
6
7
8
5. CH  
/
Buttons - Press the  
button to change to  
a higher numbered channel set into memory. Press the  
button to change to a lower numbered channel set  
into memory.  
12. VOL  
or the  
/
Buttons - Press the  
button to decrease the volume level.  
button to increase,  
1. POWER Button - Press the POWER button on the front  
panel to put the TV into standby mode.  
2. VOLUME +/Buttons - Press to raise or lower the  
volume of the sound.  
(MENU Buttons) - Press the both buttons to display the  
On-Screen menu function.  
(SET +/ Buttons) - Press to select the desired setting  
during On-Screen operations.  
3. CHANNEL +/Buttons - Press to select a higher or  
lower numbered channel set into memory.  
(Power on function) - You can also turn on the TV by  
pressing the CHANNEL + or button on the front panel  
when the TV is in standby mode.  
4. STAND BY Indicator - This indicator lights up showing  
the unit is in standby mode.  
5. ON TIMER Indicator - This indicator lights up when ON  
TIMER program is turned ON.  
6. Remote Sensor - Signals from the Remote Control unit  
are received here.  
7. AV 2 IN Jacks (Front) - Audio and video signal cables  
from an external source can be connected here.  
8. EARPHONE Jack - Plug an earphone with an 1/8  
miniplug into this jack for listening.  
13. ENTER Button - Press to enter selected setup.  
14. TV/CAP/TEXT (Closed Caption) Button - Switches  
between Caption, Text and TV modes for Closed-  
Captioned programs.  
15. CH. 1/2 Button - Switches between Channel 1 and  
Channel 2 in the Closed Caption mode.  
(Power on function) - You can also turn on the TV by  
pressing the CHANNEL  
or  
button on the remote  
control when the TV is in standby mode.  
6. MENU Button - Press to display the On-Screen menu  
function.  
7. SET +/Buttons - Press to select the desired setting  
during On-Screen operations.  
9. AC Power Cord - Connect to the AC outlet.  
10. VHF/UHF IN (ANT) Jack - Connect a VHF/UHF  
antenna or CATV cable to this jack.  
(ENTER Button) - Press to enter or select information  
for On-Screen operations.  
(RESET Button) - Press to reset the On-Screen picture  
adjustments to their factory preset positions.  
11. AV 1 IN Jacks (Rear) - Audio and video signal cables  
from an external source (ex. VCR) can be connected  
here.  
4
5
 
ANTENNA/CATV CONNECTIONS  
REMOTE CONTROL  
(CONTINUED)  
BATTERY INSTALLATION  
BATTERY PRECAUTIONS  
1. Open the battery compartment cover in the direction  
of the arrow.  
The precautions below should be followed when using  
batteries in this device:  
Combination VHF/UHF Antenna  
Single 75 ohm Cable  
This television has an extended  
tuning range and can tune most  
cable channels without using a  
cable company supplied  
converter box. Some cable  
companies offer "premium pay  
channels" in which the signal is  
scrambled. Descrambling these  
signals for normal viewing  
1.Use only the size and type of batteries specified.  
2.Be sure to follow the correct polarity when installing the  
batteries as indicated in the battery compartment.  
Reversed batteries may cause damage to the device.  
To avoid a potential short circuit, insert the “–” end first.  
3.Do not mix different types of batteries together (e.g.  
Alkaline and Carbon-zinc) or old batteries with fresh  
ones.  
300 ohm Twin-lead Wire  
Take off the Splitter  
Splitter  
requires the use of a descrambler  
300-75 ohm  
Matching Transformer  
UHF Antenna  
device which is generally  
A
V1  
IN  
V
I
D
E
O
AUDIO  
provided by the cable company.  
2. Install two AAA(penlight size) batteries, paying  
attention to the polarity diagram in the battery  
compartment.  
300 ohm Twin-lead Wire  
4.If the device is not to be used for a long period of time,  
remove the batteries to prevent damage or injury from  
possible battery leakage.  
Indoor Antenna  
VHF Antenna  
A single pole antenna is supplied with the unit (C-T1421 only),  
insert the antenna holder into the mounting hole on the back of  
the cabinet until it locks into place. Attach the antenna plug to  
the antenna jack. Adjust the length and angle of the antenna  
rod to receive the best possible picture.  
Single 75 ohm Cable  
5.Do not try to recharge batteries not intended to be  
recharged; they can overheat and rupture. (Follow  
battery manufacturers directions.)  
300 ohm Twin-lead Wire  
Combiner  
(not supplied)  
Separate VHF/UHF Antennas  
300-75 ohm  
Incoming CATV  
Matching Transformer  
Connect the 75 ohm Cable from the VHF antenna and the UHF  
antenna Twin-lead to a combiner (not supplied). Attach the  
Combiner to the Antenna Jack.  
3. Replace the compartment cover.  
NOTE:If your VHF antenna has a Twin-lead Wire, use the 300-  
75 ohm Matching Transformer, then connect the Transformer to  
the Combiner.  
Converter/Descrambler  
Converter/Descrambler  
A
B
Splitter  
A/B Switch  
For Subscribers to Basic Cable TV Service  
For basic cable service not requiring a Converter/Descrambler  
box, connect the CATV 75 ohm Coaxial Cable directly to the  
Antenna Jack on the back of the television.  
Combination VHF/UHF Antenna (Single 75 ohm  
Cable or 300 ohm Twin-lead Wire)  
Connect the 75 ohm cable from a combination VHF/UHF  
antenna to the Antenna Jack. If your combination antenna has  
a 300 ohm Twin-lead Wire, use the 300-75 ohm Matching  
Transformer.  
For Subscribers to Scrambled Cable TV Service  
If you subscribe to a cable service which requires the use of a  
Converter/Descrambler box, connect the incoming cable to the  
Converter/Descrambler box and connect the output of the box  
to the Antenna Jack on the back of the television. Follow the  
connections shown left. Set the television to the output of the  
Converter/Descrambler box (usually channel 3 or 4) and use  
the Converter/Descrambler box to select channels.  
EFFECTIVE DISTANCE OF THE REMOTE CONTROL TRANSMITTER  
Combination VHF/UHF Antenna (Separate VHF and  
UHF 300 ohm Twin-leads)  
Connect the UHF Twin-lead Wire to a Combiner (not supplied).  
Connect the VHF Twin-lead to the 300-75 ohm Matching  
Transformer. Attach the Transformer to the Combiner. Attach the  
Combiner to the Antenna Jack.  
For Subscribers to Unscrambled Basic Cable with  
Scrambled Premium Channels  
If you subscribe to a cable service in which basic cable  
channels are unscrambled and premium channels require the  
use of a Converter/Descrambler box, you may wish to use a  
two-set signal splitter (sometimes called a "two-set coupler")  
and an A/B Switch box from the cable installer or an electronics  
supply store. Follow the connections shown left. With the switch  
in the "B" position, you can directly tune any nonscrambled  
channels on your TV. With the switch in the "A" position, tune  
your TV to the output of the Converter/Descrambler box (usually  
channel 3 or 4) and use the box to tune scrambled channels.  
15 FEET  
30˚  
30˚  
NOTES: When there is an obstacle between the TV and the transmitter, the transmitter may not operate.  
When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the  
Remote sensor of the TV, the remote operation may be unstable.  
6
7
 
SETTING LANGUAGE  
CONNECTION TO OTHER EQUIPMENT  
This TV can display the channel number, on-screen displays and picture adjustments on the screen in English, Spanish or  
Portuguese.  
On-screen language selection (step 3) will automatically appear on the screen when you press the MENU button initially.  
Select the language you prefer first, then proceed with the other menu options.  
The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model  
and features of each component. Check the Users Guide provided with each component for the location of video and audio  
inputs and outputs.  
The connection diagrams in the following are offered as suggestions. You may need to modify them to accommodate your  
particular assortment of components. The diagrams are intended to show component video and audio interconnections only.  
Press the MENU button.  
M E N U  
Press the SET + or button  
3
1
2
LANGUAGE / IDIOMA  
CLOCK SET  
ON/OFF TIMER  
CH SET UP  
PICTURE  
LANGUAGE IDIOMA  
COLOR AUTO  
until the " " indicator points to  
the desired language: English  
(ENGLISH), Spanish  
(ESPAÑOL) or Portuguese  
(PORTUGUES), then press the  
ENTER button.  
Press the TV/AV button to select the AV mode to use the TV as a monitor.  
Operate your VCR as usual.  
/
Press the SET + or button to  
select the LANGUAGE mode,  
then press the ENTER button.  
+ / / ENTER / MENU  
+ / / ENTER / MENU  
TV/AV SELECTION  
If you connect the TV to VCR, camcorder, TV game or DVD you can select by pressing the TV/AV button.  
TV  
AV 1  
AV 2  
AV1  
Press the MENU button.  
Press the TV/AV button repeatedly to select the desired  
mode.  
4
NOTE:  
If Spanish or Portuguese is chosen, the Closed Caption indicators will be in the selected language, but the Closed Caption  
text will not be affected by the language selection.  
An indication of input source will display  
on the screen for 4 seconds.  
SETTING CLOCK  
1. To connect the TV to a VCR  
(ex. Use AV 1 IN jacks to connect it.)  
3. To connect the TV to a camcorder  
To playback from the camcorder, connect the camcorder  
to the TV as shown.  
You must set the time manually for CALL and ON/OFF TIMER.  
Rear of TV  
Front of TV  
VCR  
Press the MENU button.  
Press the SET + or button to set the minute.  
If you want to change the hour, press the  
RESET button.  
1
2
4
5
AV1 IN  
VIDEO  
AV2 IN  
AUDIO  
EARPHONES  
STAND BY ON TIMER  
VIDEO  
AUDIO  
M E N U  
To Audio  
Video OUT  
CLOCK SET  
ON/OFF TIMER  
CH SET UP  
PICTURE  
LANGUAGE IDIOMA  
COLOR AUTO  
VIDEO  
AUDIO  
To Audio/  
Video OUT  
Press the SET + or button  
until the indicator next to  
"CLOCK SET" begins to flash,  
then Press the ENTER button.  
VIDEO  
(not supplied)  
AUDIO  
CLOCK SET  
10 : 00  
/
(not supplied)  
+ / / ENTER / MENU  
+
/
/
ENTER  
/
RESET MENU  
/
Press the ENTER button.  
Select AV 1by pressing the TV/AV button to display  
the VCR picture.  
Select AV 2by pressing the TV/AV button to display  
the camcorder picture.  
NOTES:  
Press the SET + or –  
button to set the hour, then  
press the ENTER button.  
3
After a power failure, disconnection of the power  
plug or turning the TV power off by pressing the  
POWER button on the front panel, the time  
display will be lost. In this case, set present time  
again.  
CLOCK SET  
0 : 00  
2. To connect the TV to a TV Game  
The TV can also be used as a display device for many  
video games. However, due to the wide variety of  
different types of signal generated by these devices and  
subsequent hook-up variations required, they have not  
all been included in the suggested connection diagrams.  
You'll need to consult each component's Owner's  
Manual for additional information.  
+
/
/
ENTER  
/
RESET  
/
MENU  
When you set the minute, you can change in 10-  
minutes by holding down the SET + or button.  
COLOR SYSTEM  
The color system is automatically selected, but if the picture is not clear or no color appears, select the color system  
manually.  
To Audio/Video OUT  
Front of TV  
VIDEO  
AV2 IN  
AUDIO  
EARPHONES  
STAND BY ON TIMER  
Press the MENU button.  
TV GAME  
1
M E N U  
CLOCK SET  
ON/OFF TIMER  
CH SET UP  
PICTURE  
Press the SET + or button to select  
the COLORoption then press the  
ENTER button.  
2
LANGUAGE IDIOMA  
/
COLOR AUTO  
(not supplied)  
+ / / ENTER / MENU  
Press the ENTER button to select the  
desired COLOR SYSTEM.  
3
4
Select AV 2by pressing the TV/AV button to display  
the TV GAME picture.  
M E N U  
CLOCK SET  
ON/OFF TIMER  
CH SET UP  
PICTURE  
LANGUAGE IDIOMA  
COLOR PAL-M  
AUTO  
PAL-N  
PAL-M  
NTSC  
/
+ / / ENTER / MENU  
Press the MENU button.  
8
9
 
TV BASIC OPERATION  
TO MEMORIZE CHANNELS  
This TV is equipped with a channel memory feature which  
allows channels to skip up or down to the next channel set  
into memory, skipping over unwanted channels.  
Before selecting channels, they must be programmed into  
the TV's memory. In addition to normal VHF and UHF  
channels, this TV can receive up to 113 Cable TV channels.  
To use this TV with an antenna, set the TV/CATV menu  
option to the TV setting. When shipped from the factory, this  
menu option is in the CATV setting.  
AUTOMATIC CHANNEL MEMORY  
QUICK VIEW button  
Returns to the channel viewed just before the channel  
currently onscreen.  
1
Press the POWER button on the front panel to put the  
TV into standby mode. The STAND BY indicator will  
light.  
Press the MENU button.  
M
E
N
U
1
CLOCK SET  
ON/OFF TIMER  
CH SET UP  
PICTURE  
LANGUAGE  
COLOR AUTO  
Press the SET + or button until the  
/
IDIOMA  
2
Press the POWER button on the remote control to turn  
on the TV.  
You can also turn on the TV by pressing the CHAN-  
NEL UP or DOWN button on the front panel or on the  
remote control when the TV is in standby mode.  
2
CH 012  
CH 007  
indicator next to "CH SET UP" begins  
to flash, then press the ENTER  
button.  
+
/
/
ENTER MENU  
/
TV/CATV SELECTION  
Press the SET + or button until the  
indicator next to "AUTO CH  
CH SET UP  
TV CATV  
AUTO CH MEMORY  
ADD DELETE  
3
The VOLUME can be adjusted to a desired level by  
Press the MENU button.  
3
1
2
MUTING button  
/
MEMORY" begins to flash, then press  
the ENTER button. The TV will begin  
memorizing all the channels available  
in your area.  
pressing the VOL (VOLUME)  
Adjust the volume level by  
or  
button.  
MUTING  
The MUTING button instantly turns the  
volume down completely when you  
press it.  
Press MUTING button and the volume  
level will instantly go to zero. To restore  
+
/
/
ENTER MENU  
/
M
E
N
U
Press the SET + or button until the  
indicator next to "CH SET UP"  
begins to flash, then press the  
ENTER button.  
CLOCK SET  
ON/OFF TIMER  
CH SET UP  
PICTURE  
pressing the VOL  
or  
button. The volume level will be  
indicated on the screen by  
LANGUAGE  
/
IDIOMA  
COLOR AUTO  
ENTER / MENU  
+
/
/
Press the MENU button.  
4
green bar. As the volume level  
increases, so do the number of  
bar. If the volume decreases,  
the volume to its previous level, press MUTING button again.  
VOLUME  
32  
Press the SET + or button until the  
indicator next to "TV/CATV" begins  
to flash.  
3
TO ADD/DELETE CHANNELS  
the number of green bar also decreases.  
10-key pad (0-9)  
Press the MENU button.  
M
E
N
U
1
CH SET UP  
TV CATV  
Press these buttons to select a channel. The channel  
number will appear on the upper right corner of the TV  
screen. If an invalid channel number is selected, the display  
will revert to the original channel.  
CLOCK SET  
ON/OFF TIMER  
CH SET UP  
PICTURE  
The sound level will be indicated on the TV screen by  
green bars and a number. As the sound level in-  
creases, so do the number of bars and the number on  
the screen. The same is true for decreasing the level.  
AUTO CH MEMORY  
ADD DELETE  
/
Press the SET + or button until the  
LANGUAGE  
COLOR AUTO  
/
IDIOMA  
2
Press the ENTER button to select  
the TV or CATV mode. The arrow  
indicates the selected mode.  
4
5
indicator next to "CH SET-UP" begins  
to flash, then press the ENTER  
button.  
+
/
/
ENTER MENU  
/
ENTER MENU  
+
/
/
/
TV Mode Direct Channel Selection  
Set the TV/CATV menu option to the appropriate  
position. When shipped from the factory, this menu  
option is in the CATV setting. See "TO MEMORIZE  
CHANNELS".  
Press the MENU button.  
4
5
When the TV/CATV menu option is in the TV position, all  
channels can be instantly selected by using two buttons.  
(For example, to select channel 2, press "0", then "2". If you  
press only "2", channel selection will be delayed for a few  
seconds). For channels 10 and above, press the 2 digits in  
order.  
Press the SET + or button until the  
CH SET UP  
TV CATV  
AUTO CH MEMORY  
ADD DELETE  
3
indicator next to "ADD/DELETE"  
begins to flash, then press the  
ENTER button.  
/
NOTE: Contact your cable company to determine the  
+
/
/
ENTER MENU  
/
type of cable system used in your area.  
Select the desired channels to be  
added or deleted using the 10-key  
TV  
-
-
VHF/UHF channels  
CABLE TV channels  
4
CATV  
pad (0-9) or the CH + or button.  
CATV Mode Direct Channel Selection  
When the TV/CATV menu option is in the CATV position,  
channels can be selected as follows:  
Press the ENTER button to select ADD or DELETE.  
CH (CHANNEL)  
Press and release the CH  
(CHANNEL) or button.  
and  
buttons  
5
If an unmemorized channel was selected (step 4), the  
channel indication will be red. Press the CH + or –  
button if you wish to ADD the unmemorized channel.  
The channel indicator will change from red to green  
when a channel is added and the channel will be  
memorized. If a memorized channel was selected (step  
4), the channel indication will be green.  
CH 012  
CH. 1-9  
Press "0" twice, then 1-9 as needed.  
Example, to select channel 2, press  
"002".  
The channel automatically stops  
at the next channel set into  
memory.  
CH. 10-12  
CH. 13-99  
Press "0", then remaining 2 digits.  
Example, to select channel 12, press  
"012".  
Press the 2 digits in order.  
Example, to select channel 36, press  
"36".  
For proper operation, before selecting channels,  
they should be set into the TV's memory.  
See "TO MEMORIZE CHANNELS".  
Press the CH + or button if you wish to DELETE the  
channel from memory. The channel  
indicator will change from green to  
red when a channel is deleted.  
Repeat Steps 4 and 5 for each  
channel to be added or deleted.  
ADD  
CH 012  
CH. 100-125 Press the 3 digits in order.  
Example, to select channel 120, press  
+
/
/
0
-9 / ENTER / MENU  
"120".  
Press the MENU button after adding or deleting all of  
the desired channels, to return to normal TV viewing.  
6
NOTE: If the station being viewed stops broadcasting, the  
TV will automatically shut off after 15 minutes.  
10  
11  
 
SLEEP TIMER button  
CLOSED CAPTION  
Text: The Text Closed Caption Mode will usually fill 1/2 of  
full screen with a programming schedule or other  
The Sleep Timer can turn the TV off for you after you fall  
asleep. Program it to work in intervals of 10 minutes, for  
a total time of up to 120 minutes.  
To change the sleep timer setting:  
Press the SLEEP button repeatedly until the display  
turns to desired time.  
To cancel the sleep time:  
Press the SLEEP button repeatedly until the display  
turns to 0.  
WHAT IS CLOSED CAPTIONING?  
This television has the capability to decode and display  
Closed Captioned television programs. Closed  
Captioning will display text on the screen for hearing  
impaired viewers or it will translate and display text in  
another language.  
information. After selecting a Closed Caption Mode, it will  
stay in effect until it is changed, even if the channel is  
changed. If the Captions signal is lost due to a commercial  
or a break in the signal, the Captions will reappear when  
the signal is received again. If the channels are changed,  
the Captions will be delayed approximately 10 seconds.  
The Captions will appear in places on the screen where  
they will least interfere with the picture, usually on the  
bottom of the screen. News programs will usually show  
three-line Closed Captions which scroll onto the screen.  
Most other shows provide two or three lined Captions  
placed near the character who is speaking so the viewer  
can follow the dialogue. Words in italics or underlined  
describe titles, words in foreign languages or words  
requiring emphasis. Words that are sung usually appear  
enclosed by musical notes. For television programs  
broadcasting with Closed Captions, look in your TV guide  
for the Closed Captions symbol (CC).  
SLEEP  
120  
TO VIEW CLOSED CAPTIONS  
Press the TV/CAP/TEXT button on the remote control to  
switch between normal TV and the two Closed Caption  
Modes (Captions and 1/2 of Full Screen Text).  
CALL button  
Press the CALL button to display the current informations on the screen.  
Captions: This Closed Caption Mode will display text on  
the screen in English or another language (depending on  
the setting of the Closed Captions CH. 1/2 button).  
Generally, Closed Captions in English are transmitted on  
Captions Channel 1 and Closed Captions in other  
languages are transmitted on Captions Channel 2.  
Press Once  
Press Twice  
Press 3 times  
Channel No.  
8 : 30  
PAL-M  
CH 012  
CLOCK  
Color System  
CAPTION CH1  
CAPTION CH1  
Closed Caption*  
Closed Caption*  
When activating the Closed Captioned Decoder, there will be a short delay before the Closed Captioned text appears  
on the screen.  
Closed Captioned text is only displayed in locations where it is available.  
Clear the current  
informations**  
This indication dose not appear when the Closed Capition is not active.  
In the AV mode, AV 1or AV 2continues to display when there is no signal.  
*
**  
If no caption signal is received, no captions will appear, but the television will remain in the Caption Mode.  
Misspellings or unusual characters may occasionally appear during Closed Captioning. This is normal with Closed  
Captioning, especially with live programs. This is because during live programs, captions are also entered live.  
These transmissions do not allow time for editing.  
When Captions are being displayed, on-screen displays, such as volume and MUTING may not be seen or may  
interfere with Closed Captions.  
Some cable systems and copy protection systems may interfere with the Closed Captioned signal.  
If using an indoor antenna or if TV reception is very poor, the Closed Caption Decoder may not appear or may  
appear with strange characters or misspelled words. In this case, adjust the antenna for better reception or use an  
outdoor antenna.  
PICTURE ADJUSTMENTS  
You can adjust the settings for color, sharpness, con-  
Press the SET + or button to adjust the setting.  
4
trast, brightness, tint (NTSC only) and component.  
Press the MENU button.  
1
+
increase brightness  
increase contrast  
be brilliant color  
be greenish color  
decrease brightness  
decrease contrast  
be pale color  
BRIGHTNESS  
CONTRAST  
COLOR  
TINT (NTSC only)  
SHARPNESS  
2
Press the SET + or button  
until the indicator next to  
"PICTURE" begins to flash,  
then press the ENTER button.  
M E N U  
CLOCK SET  
ON/OFF TIMER  
CH SET UP  
be reddish color  
PICTURE  
LANGUAGE IDIOMA  
/
makes picture clearer makes picture softer  
COLOR AUTO  
+ / / ENTER / MENU  
TO RETURN TO INITIAL SETTING  
Press the RESET button while the picture adjusting mode  
appears on the screen (except the adjusting component).  
3
Press the ENTER button  
repeatedly to select the  
item you want to adjust.  
BRIGHTNESS  
0
NOTE: The on-screen display will disappear 6 seconds  
after finishing an adjustment. The settings can  
only be adjusted when they are displayed on  
the TV screen.  
+ / / ENTER / RESET / MENU  
BRIGHTNESS  
CONTRAST  
COLOR  
SHARPNESS  
TINT  
(NTSC only)  
12  
13  
 
TROUBLESHOOTING GUIDE  
ON/OFF TIMER  
Before requesting service, please refer to the following chart for the symptom and possible solution.  
ON TIMER SETTING  
This feature allows you to have the TV automatically turn "ON" at predetermined time.  
SYMPTOMS  
POSSIBLE SOLUTIONS  
Make sure the power cord is plugged in.  
If you program the "ON" timer once the timer will turn "ON" the TV daily at the same time and to the same channel.  
If the power has been turned on at programmed time, the channel is changed to a programmed one.  
Try another AC outlet.  
Power is off, check fuse or circuit breaker.  
Unplug unit for an hour, then plug it back in.  
TV does not operate  
Press the MENU button.  
Press the SET + or button  
to set the minute, then press  
the ENTER button.  
1
2
5
ON/OFF TIMER  
ON TIMER  
7:00  
CH012  
CANCEL  
CANCEL  
Press the SET + or button until  
the indicator next to "ON/OFF  
TIMER" begins to flash, then  
press the ENTER button.  
M E N U  
Station or CATV experiencing problems, tune to another station.  
Check sound adjustments (Volume and Muting).  
Check for sources of possible interference.  
CLOCK SET  
ON/OFF TIMER  
CH SET UP  
PICTURE  
LANGUAGE IDIOMA  
COLOR AUTO  
OFF TIMER  
0:00  
You can change in 10-  
minutes step by holding  
down the SET + or –  
button.  
Poor sound or No sound  
Poor picture or No picture  
+ / / ENTER / RESET / MENU  
/
Station or CATV experiencing problems, tune to another station.  
Make sure channels are set into memory.  
Check antenna or CATV connections, reorient antenna.  
Check for sources of possible interference.  
+ / / ENTER / MENU  
Press the SET + or button until  
the indicator next to "ON TIMER"  
begins to flash, then press the  
ENTER button.  
3
4
ON/OFF TIMER  
ON TIMER  
Press the SET + or  
6
Check picture control adjustments.  
ON/OFF TIMER  
ON TIMER  
0:00  
CH012  
button to set the channel,  
then press the ENTER  
button.  
CANCEL  
7:30  
CH012  
CANCEL  
CANCEL  
Station or CATV experiencing problems, tune to another station.  
Make sure channels are set into memory.  
Station signal is weak, reorient antenna to receive desired station.  
Check for sources of possible interference.  
OFF TIMER  
0:00  
CANCEL  
OFF TIMER  
0:00  
Poor reception on some channels  
Poor color or no color  
You can set the channel  
which is added in the  
CH SET UP option.  
+ / / ENTER / RESET / MENU  
+ / / ENTER / RESET / MENU  
Press the SET + or button to set  
the hour, then press the ENTER  
button. If you want to change the  
hour, press the RESET button.  
Station or CATV experiencing problems, tune to another station.  
Make sure channels are set into memory.  
Check picture control adjustments.  
Check antenna or CATV connections, reorient antenna.  
Check for sources of possible interference.  
Check the color system.  
ON/OFF TIMER  
ON TIMER  
0:00  
CH012  
CANCEL  
Press the SET + or –  
button to select the  
SET mode.  
7
8
ON/OFF TIMER  
ON TIMER  
OFF TIMER  
0:00  
7:30  
CH007  
CANCEL  
CANCEL  
+ / / ENTER / RESET / MENU  
OFF TIMER  
0:00  
CANCEL  
Station or CATV experiencing problems, tune to another station.  
Make sure channels are set into memory.  
CATV company is scrambling signal.  
+ / / ENTER / RESET / MENU  
Picture wobbles or drifts  
No CATV reception  
Press the MENU button.  
Check antenna orientation.  
NOTES:  
You cannot set the ON/OFF TIMER when the clock is not set.  
This TV will automatically turn off approximately 1 hour later after the ON TIMER turns on the TV unless any  
buttons are pressed.  
To cancel the ON TIMER function:  
Check all CATV connections.  
Set TV/CATV menu option to the CATV mode.  
Station or CATV system problems, try another station.  
Check antenna connections, reorient antenna.  
Check for sources of possible interference.  
To cancel ON TIMER in step 7 above press the SET + or button to select the CANCEL mode.  
Horizontal or diagonal bars on screen  
No reception above channel 13  
OFF TIMER SETTING  
Make sure TV/CATV menu option is in the appropriate mode.  
If using antenna, check UHF antenna connections.  
This feature allows you to have the TV turn "OFF" automatically at a predetermined time.  
If you program the OFF TIMER once, The TV will be automatically turned off at the same time daily.  
Batteries are weak, dead or inserted incorrectly.  
Remote is out of range, move closer to TV within (15 feet).  
Make sure Remote is aimed at sensor.  
Confirm there are no obstructions between the Remote and the TV.  
Make sure the power cord is plugged in.  
Press the SET + or –  
button to set the hour,  
then press the  
Press the MENU button.  
4
1
2
ON/OFF TIMER  
ON TIMER  
No Remote operation  
TV shuts off  
7:30  
CH012  
CANCEL  
Press the SET + or button until  
the indicator next to "ON/OFF  
TIMER" begins to flash, then  
press the ENTER button.  
M E N U  
OFF TIMER  
0:00  
ENTER button.  
CLOCK SET  
ON/OFF TIMER  
CH SET UP  
PICTURE  
CANCEL  
If you want to change the  
hour, press the RESET  
button.  
No broadcast on station tuned.  
Sleep Timer is set.  
ON/OFF TIMER is set.  
Power interrupted.  
+ / / ENTER / RESET / MENU  
LANGUAGE IDIOMA  
/
COLOR AUTO  
+ / / ENTER / MENU  
ON/OFF TIMER  
ON TIMER  
5
Press the SET + or –  
button to set the minute  
then press the ENTER  
button.  
You can change in 10-  
minutes step by holding  
Approximately 1 hour has passed after the ON TIMER turns on and no button was  
pressed (See page 14).  
3
7:30  
CH012  
Press the SET + or button  
until the indicator next to "OFF  
TIMER" begins to flash, then  
press the ENTER button.  
ON/OFF TIMER  
ON TIMER  
CANCEL  
CANCEL  
7:30  
CH012  
OFF TIMER  
11:00  
TV station experiencing problems or program tuned is not closed captioned.  
Try another channel.  
Check CATV connection or VHF/UHF antenna, reposition or rotate antenna.  
Press TV/CAP/TEXT button to turn on the closed caption decoder.  
CANCEL  
CANCEL  
Closed - Caption is not activated.  
OFF TIMER  
0:00  
+ / / ENTER / RESET / MENU  
+ / / ENTER / RESET / MENU  
down the SET + or button.  
Select proper language in the menu options.  
Display is not shown in your language.  
ON/OFF TIMER  
ON TIMER  
Press the SET + or –  
button to select the SET  
mode.  
6
7
7:30  
CH012  
CANCEL  
CANCEL  
OFF TIMER  
11:30  
+ / / ENTER / RESET / MENU  
Press the MENU button.  
NOTES:  
If station being viewed stops broadcasting, the TV will automatically shut itself off after 15 minutes.  
To cancel the OFF TIMER function:  
To cancel OFF TIMER, in step 7 above press the SET + or button to select the CANCEL mode.  
14  
15  
 

Ingersoll Rand Power Screwdriver 1R User Manual
Intel Computer Hardware SOM 4486 User Manual
JVC Portable CD Player RD T50LB User Manual
JVC Speaker System UXG28 User Manual
K2 Bike Bicycle Accessories K2 BICYCLE User Manual
Kenwood Car Stereo System CAW 1142 02 User Manual
KitchenAid Double Oven KEBK276SBL04 User Manual
KitchenAid Microwave Oven KBHV109 User Manual
Kodak Camcorder 4H7269 User Manual
Korg Musical Instrument KPC 1 EFG User Manual