Iomega Marine Instruments 104 User Manual

LAQ-XXXX, Green Label Thinners  
®
OMEGALAQ Temperature Indicating Liquids  
INSTRUCTION  
M1319/0104  
SHEET  
GENERAL DESCRIPTION: OMEGALAQ® Temperature Indicating Liquid (LAQ) OMEGAMARKER® consist of a temperature  
melt material in a liquid form. They are made from the same material used in the OMEGAMARKER® temperature indicating  
products this time in a lacquer suspension. Lacquer serves as a transport function only. The OMEGALAQ® temperature  
indicating liquids are used to tell temperatures on surfaces such as polished metal, glass, plastics, rubber, fabrics or  
electronic components. They can be used for making large marks which can be viewed at a distance. These temperature  
indicating liquids are widely used for monitoring critical temperatures in the electronics field, such as preheat temperatures for  
wave soldering. Other applications include dielectric heatsealing, postforming plastic laminate, and annealing polished metal  
surfaces.  
®
The OMEGALAQ liquids (LAQ) have a time response on the order of milliseconds (0.001 sec.). They are available in many  
temperature ratings. The OMEGALAQ® liquids have an accuracy of 1% of the rated temperature.  
DIRECTIONS FOR USE:  
LIQUID TYPE: Shake and/or stir jar contents well just prior to use. Apply a thin coating by using a brush to the surface being  
tested before the object being tested is brought up to temperature. It dries almost instantly to a dull opaque finish. When its  
specific temperature is reached, the opaque finish liquifies abruptly. The melted material does not revert to its original opaque  
appearance but remains glossy and transparent upon cooling.  
OMEGALAQ® liquids can be diluted to any desired consistency without changing its melting point. The thinner the coating  
used, the quicker the reaction time will be when the rated temperature has been reached. When thinning, use OMEGA’s  
OMEGALAQ® Green Label Thinner only.  
REMOVAL AND CLEANING: For lacquers with temperature ratings of 650°F or below, the unheated mark can be removed  
with alcohol or water. For ratings above 650°F, use water only. If the mark has been heated well above the rated temperature  
and has become charred, an abrasive procedure may be required for removal.  
®
OMEGALAQ LIQUIDS IN A VACUUM: The following rated OMEGALAQ® liquids are the best candidates for high vacuum  
work. They show relatively little loss of substance in a vacuum at the temperature level of their respective melting points,  
compared to other OMEGALAQ® products of nearby temperatures.  
TEMPERATURES (°F)  
175  
200  
225  
325  
475  
1150 1500 1800  
2000  
488 1200 1600 1900  
500 1250 1700  
700 1300  
750  
Bear in mind that prolonged heating in a high vacuum, or heating to a temperature well above the melting point, some  
sublimation or evaporation is to be expected. Thus, the user needs to check the suitability of OMEGALAQ® products under  
the temperature/pressure/time regime planned. OMEGA assumes no responsibility for the use of OMEGALAQ® products  
under vacuum conditions.  
SHELF LIFE: Temperature indicating Products have a limited shelf life. By verifying the melting point of the lacquers at six-  
month intervals, the effective shelf life of these products may be extended indefinitely. If they have dried out, OMEGALAQ®  
products may be liquefied by using the Green Label Thinner. See directions for use and warranty for further information.  
 

Insignia Camcorder NS DV720PBL2 User Manual
JBL Home Theater System ESC200 User Manual
John Deere Lawn Mower GM1190 User Manual
JVC Flat Panel Television GR D20 User Manual
JVC Stereo System UX M5 User Manual
Kalorik Espresso Maker EXP 25022 User Manual
Kambrook Vacuum Cleaner KVC23 User Manual
Kenwood Stereo System XD 652 User Manual
KitchenAid Food Processor KFP0922 User Manual
Knoll Projector HDP460 User Manual